Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for StoneAge SPINCAT SC-125
Summary of Contents for StoneAge SPINCAT SC-125
- Page 1 SPINCAT SC 125 ROTARY NOZZLE USER MANUAL PL 625 REV B (05/2018)
-
Page 2: Table Of Contents
TABLE OF CONTENTS MANUFACTURER’S INFORMATION ............3 SPECIFICATIONS. -
Page 3: Manufacturer's Information
MANUFACTURER’S INFORMATION StoneAge Inc. StoneAge Europe 466 S. Skylane Drive Unit 2, Britannia Business Centre Durango, CO 81303, USA Britannia Way Phone: 970-259-2869 Malvern WR14 1GZ Toll Free: 866-795-1586 United Kingdom www.stoneagetools.com Phone: +44 (0) 1684 892065 This manual must be used in accordance with all applicable national laws. The manual shall be regarded as a part of the machine and shall be kept for reference until the final dismantling of the machine, as defined by applicable national law(s). -
Page 4: System Assembly - Overview
An internal fluid speed control maintains rotation speeds of 10 to 50 rpm. The Spincat uses a synthetic silicone viscous fluid for lubrication. The fluid is available from StoneAge as part number BJ 048-S. The tool has a straight flow-through design with a leak-free high pressure seal so pump power is not wasted. -
Page 5: Pre-Rih Checklist
PRE-RIH CHECKLIST PRE-RIH CHECKLIST: • After receipt on location, visually inspect the SpinCat™ to ensure no small debris has entered the tool. NOTE: The SpinCat™ package includes a briefcase size Pelican® case. We recommend keeping the SpinCat™ and spare set screws and other parts inside the case. -
Page 6: Lubricant Replacement Instructions
LUBRICANT FILL INSTRUCTIONS TOPPING OFF LUBRICANT: The Spincat uses synthetic silicone viscous fluid for a lubricant. To top off the tool with lubricant, follow steps below. If the tool is being rebuilt or the seal replaced, the lubricant should be poured directly into the body around the shaft before the inlet nut is installed. -
Page 7: High Pressure Seal Replacement
HIGH PRESSURE SEAL REPLACEMENT TO REPLACE THE HIGH PRESSURE SEAL: Unscrew the Inlet Nut (SC125 002-AMMT) and remove the Port Plug Assembly (FT 026). 2. Remove the old Seat (SC168 011-C) and H.P. Seal (SC168 012-O). 3. Apply grease to and install new H.P. Seal into the shaft with the O-Ring groove end going in first. -
Page 8: Disassembly
DISASSEMBLY TO DISASSEMBLE THE SPINCAT SC-125: Unscrew the Inlet Nut (SC125 002-AMMT) from the body. 2. Remove the Port Plug Assembly (FT 026) from the Nut. 3. Remove the Seat (SC168 011-C) and the H.P. Seal (SC168 012-O) from the bore of the shaft. - Page 9 DISASSEMBLY 7. Unscrew the Inlet End Shaft (SC125 001.1) from the Outlet End Shaft/Head assembly and remove both from the Body. 8. Pull the Bearing (SC125 009) from the Inlet End Shaft. 9. If the O-Ring (SC125 016) is damaged, remove it from the bore of the Inlet End Shaft. 10.
-
Page 10: Assembly
ASSEMBLY TO ASSEMBLE THE SPINCAT SC-125: A StoneAge Seal Tool (SC125 050) is available to aid in installing the Seals in the Body and Nut. Install Shaft Seals (SC125 007) into Body (SC125 003). Note direction of lip with spring on each Seal. - Page 11 ASSEMBLY 6. Thread the Head (SC125 043-X) onto Outlet End Shaft (SC125 001.2). Use Threadmate and fluorocarbon tape on the pipe threads. NOTE: there is a 1/4" hex on the inside diameter of the Shaft for holding the Shaft when tightening. Tighten to 30 ft-lbs. Apply anti-seize to straight threads of the Shaft.
-
Page 12: Troubleshooting
TROUBLESHOOTING HIGH-PRESSURE SEAL LEAK: • The high pressure seal may leak initially at lower pressures, but should pop closed as pressure is increased. A continuous leak at operating pressure from the weep holes indicates the need to replace the HP Seal and Seat. HP Seals wearing out too quickly can be an indication that the HP Seat is installed upside-down, or the tool is rotating too fast. - Page 13 NOTES THIS PAGE LEFT INTENTIONALLY BLANK 866-795-1586 • WWW.STONEAGETOOLS.COM...
-
Page 14: Replacement Part Wear Information
REPLACEMENT PART WEAR INFORMATION • BODY AND INLET NUT WEAR: Follow these wear dimension guidelines to determine when to replace parts. Common scuffing Common scuffing wear pattern on wear pattern on Inlet Body Ø 1.182 Ø 1.225 Minimum at Minimum at head end inlet nut end SC125 003 Body Scuffing Wear... -
Page 15: Maintenance, Parts, And Overhaul Kits
MAINTENANCE PARTS & OVERHAUL KITS PARTS OVERVIEW SC125 001.1 Shaft, Inlet End SC168 012-O H.P. Seal Assembly SC125 006 Shaft Seal SC125 021 SC125 026 Port Plug Weep Seal SC125 016 Assembly O-Ring, Viton SC125 002-AMMT SC125 009 Inlet Nut Bearing SC168 011-C Seat, Carbide... -
Page 16: Terms And Conditions And Warranty
REPRESENTATIONS AS TO THE PERFORMANCE Conditions”) shall operate as the acceptance by OF ANY PRODUCT EXCEPT AS SET FORTH IN THE StoneAge, Inc. (“Seller”) of the order submitted by STONEAGE LIMITED WARRANTY PROVIDED WITH THE the purchaser (“Buyer”). Such acceptance is made PRODUCT. - Page 17 STONEAGE TRADEMARK LIST View the list of StoneAge’s trademarks and service marks and learn how the trademarks should be used. Use of StoneAge trademarks may be prohibited, unless expressly authorized. http://www.StoneAgetools.com/trademark-list/ STONEAGE PATENT DATA View the list of StoneAge’s current U.S.
- Page 18 Product at any time without notice to End- directly from StoneAge Inc. (“StoneAge”) or from a User, and StoneAge is not obligated to make the same StoneAge Authorized Dealer or Reseller (“Dealer”). No improvements during warranty service to any Product warranty of any kind or nature is made by StoneAge previously manufactured.
- Page 19 LIABILITY ARE PART OF THE CONSIDERATION IN User shall familiarize itself with all operation materials THE PRICE OF THE STONEAGE PRODUCT YOU provided by StoneAge and shall at all times use and PURCHASED. require its agents, employees and contractors to use...
- Page 20 1-866-795-1586 • www.STONEAGETOOLS.com © 2015 StoneAge, Inc. All Rights Reserved...
Need help?
Do you have a question about the SPINCAT SC-125 and is the answer not in the manual?
Questions and answers