Related Manuals for Kinpo A300A
Summary of Contents for Kinpo A300A
- Page 1 Kinpo Electronics, Inc. ADSL PC Network Interface Modem Model No.: A300A Installation Guide Microsoft Windows 95, 98, and NT4.0 Version : E1 Date : Jan. 25, 2000...
-
Page 2: Table Of Contents
Trouble Shooting ............................19 Connector Pinout ............................20 Appendix B – Upgrade Microsoft DUN Version 1.3..................21 Appendix C – Verifying Dial-Up Networking (DUN) Status..............22 Appendix D – Removing A300A Drivers ....................23 Windows 95, 98............................23 Windows NT4.0............................23 Appendix E – Verifying/Changing the ADSL Mode .................24 Appendix F –... -
Page 3: System Requirements
Appendix A on how to upgrade your system’s DUN. HARDWARE INSTALLATION WARNING! To avoid possible damage to your A300A card you need to use an anti-static grounding device or hold onto the metal chassis of the PC to provide anti-static grounding. -
Page 4: Windows 95A
POINT TO POINT SERVI CE FOR WINDOWS 95A After installing the A300A card, power on the PC system. The Hardware Wizard will detect the card as a PCI Network Controller. Select the Driver from disk provided by hardware manufacturer option. Click OK. -
Page 5: Windows 95B
Insert the A300A Driver CD into the CD drive. Then click Other Locations . NOTE : If the driver is not detected, click Back, insert the A300A Driver CD, then click NEXT. When the Select Other Location window appears, enter <CD drive letter> :\Driver\PPPoA9x (e.g. -
Page 6: Windows 98, 98A
At the conclusion of the A300A driver installation, the Add New Hardwa re window appears. Click Finish. For the PC system to properly set up the A300A , a system Restart is required. Click Yes. NOTE : After restarting the system, the Diagnostic Tools icon is active and monitoring connectivity. - Page 7 ITU G.992.1 Annex A (G.dmt) ....referred to as G.dmt ITU G.992.2 Annex A/B (G.lite)....referred to as G.lite ANSI T1.413 Issue 2........referred to as ANSI 21. After you select and check your ISP’s service mode, click Set. Congratulations, you are done. Your A300A the Internet is established!
-
Page 8: Windows Nt 4.0
Click Add (to add new adapters). In the Select Network Adapter window click Have Disk. Insert the A300A Driver CD into the CD-ROM drive, enter the < CD drive letter> :\Driver\PPPoANT4 (e.g. D:\Driver\PPPoANT4), then click OK. The Select OEM Option window will find the ITeX ADSL PCI NIC driver, Click OK. The system will copy the drivers to the hard drive. - Page 9 17. After the s ystem restarts the Diagnostic Tools icon will appear on the task bar. When the A300A card is connected to the ADSL data port, both panels of the icon will appear black signifying an ADSL connection. 18. To begin a dial-up connection, double -click My Computer, then double-click Dial-Up Networking.
-
Page 10: Pppoa Adsl Network Connection
ITU G.992.1 Annex A (G.dmt) ....referred to as G.dmt ITU G.992.2 Annex A/B (G.lite)....referred to as G.lite ANSI T1.413 Issue 2........referred to as ANSI 11. After you select and check your ISP’s service mode, click Set. Congratulations, you are done. Your A300A the Internet is established! -
Page 11: Ip Protocol Over Atm (Ipoa) Or (Rfc 1577) For Windows 98 2Nd Edition
10. At the conclusion of the A300A driver installation, click Finish. 11. For the PC system to properly set up the A300A, a system Restart is required. Click Yes. 12. After restarting the system, the Diagnostic Tools icon is active and monitoring connectivity. - Page 12 ITU G.992.1 Annex A (G.dmt) ....referred to as G.dmt ITU G.992.2 Annex A/B (G.lite)....referred to as G.lite ANSI T1.413 Issue 2........referred to as ANSI 14. After you select and check your ISP’s service mode, click Set. Congratulations, you are done. Your A300A the Internet is established!
-
Page 13: Bridged Ethernet Over Atm (Beoa ) Or (Rfc 1483)
BRIDGED ETHERNET SERVICE FOR WINDOWS 95A After installing the A300A card, power on the PC system. The Hardware Wizard will detect the A300A as a PCI Network Controller. Select the Driver from disk provided by hardware manufacturer option. Insert the A300A Driver CD into the drive. -
Page 14: Windows 95B
BRIDGED ETHERNET SERVICE FOR WINDOWS 95B After installing the A300A card, power-up the PC System. The Hardware wizard will detect the A300A as a PCI Network Controller, click Next. Insert the A300A Driver CD into the CD-ROM drive. Click Other Locations . -
Page 15: Windows 98, 98A
BRIDGED ETHERNET FOR WINDOWS 98, 98A After installing the A300A card and restarting the system, the Add New Hardware Wizard window will automatically appear and indicate that a new PCI Network Controller has been found. Click Next. Then select Search for the best driver for your device. Click Next. -
Page 16: Bridged Ethernet Adsl Service Configuration
ITU G.992.1 Annex A (G.dmt) ....referred to as G.dmt ITU G.992.2 Annex A/B (G.lite)....referred to as G.lite ANSI T1.413 Issue 2........referred to as ANSI 15. After you select and check your ISP’s service mode, click Set. Congratulations, you are done. Your A300A the Internet is established! -
Page 17: Windows Nt 4.0
Click Add (to add new adapters). In the Select Network Adapter window click Have Disk. Insert the A300A Driver CD into the drive, enter the < CD drive letter> :\Driver\1483NT4 (e.g.D:\Driver\1483NT4) and click OK. The Select OEM Option window will find the ITeX ADSL PCI NIC. Click OK. The system will copy the drivers to the hard drive. - Page 18 ITU G.992.1 Annex A (G.dmt) ....referred to as G.dmt ITU G.992.2 Annex A/B (G.lite)....referred to as G.lite ANSI T1.413 Issue 2........referred to as ANSI 16. After you select and check your ISP’s service mode, click Set. Congratulations, your A300A the Internet is established!
-
Page 19: Editing Bridged Ethernet Adsl Service Configuration
Note: Please refer to your ISP for the TCP/IP Properties. Select the DNS configuration tab and enter (or edit) the following fields: Enter the Host Name (e.g. A300A) and Domain (e.g. pacbell.net). Note: To enter the Domain search (DNS) entries, click Add then enter the address. Click Add to save the address. -
Page 20: Appendix A - Diagnostic Tools
Yes to begin the diagnostic program or click No to exit diagnostic program. The Diagnostic program performs a brief hardware check and displays the hardware status. If the A300A fails the Diagnostic tests (shown below), then record the test result and contact customer support. -
Page 21: Configuring The Connection Service
è ADSL bridge - PCI I/O Test I90188 chip test Pass è I90135 Register Test I90135 chip test Pass è I90135 Memory Test I90135 chip test Pass è ADSL Bridge - Loopback I90188 Fast datapath Trial 20, Pass 20 è …Interleave datapath Trial 20, Pass 20 è... -
Page 22: Connector Pinout
– identified by the ADSL installation. The center two pins, pins 3 and 4, are used for ADSL data. For the A300A card to make a proper ADSL connection, the installed ADSL data port should also use pins 3 and 4 for data. -
Page 23: Appendix B - Upgrade Microsoft Dun Version 1.3
APPENDIX B - UPGRADE MICROSOFT DUN VERS ION 1.3 This section explains how to upgrade Microsoft’s Dial-Up Networking (DUN) application. You can download the DUN application from Microsoft’s Web page and install it into your system. Please follow the instruction below. Access the Microsoft Web site at http://www.microsoft.com In the Contents frame, select Free Downloads. -
Page 24: Appendix C - Verifying Dial-Up Networking (Dun) Status
APPENDIX C – VERIFYI NG DIAL-UP NETWORKING (DUN) STATUS It is possible to have Dial-Up Networking (DUN) version 1.2B or above, but not have the Dial- Up Networking components loaded in the Windows environment. This procedure is for determining the status of DUN on the PC system. At the task bar click Start, Settings, Control Panel and double-click on Add/Remove Programs . -
Page 25: Appendix D - Removing A300A Drivers
APPENDIX D – REMOVING A300A DRIVERS WINDOWS 95, 98 To Delete A300A drivers; on the desktop, right-click on My Computer, then select Properties , then click on the Device Manager tab, then double click Network adapters. Select the ITeX ADSL PCI NIC, then click on the Remove button. -
Page 26: Appendix E - Verifying/Changing The Adsl Mode
ITU G.992.2 Annex A/B (G.lite)....referred to as G.lite ANSI T1.413 Issue 2........referred to as ANSI 3. After you select and check your ISP’s service mode, click Set. The ATM mode has been set and you are ready to enjoy your A300A the Internet. -
Page 27: Appendix F - System Requirements & Compliance Information
APPENDIX F - SYSTEM REQUIREMENTS & COMPLIANCE INFORMATION Power Requirements • .75A Max @ +5V ± 5%, 0.1A max @ ± 12V, ± 5% Environmental Requirements • Operating Temperature: 0 °C to 70°C with airflow • Non-operating Temperature: -10 °C to 85 °C •... -
Page 28: Appendix G - Copyright & Regulatory Information
This manual and software described in it are copyrighted with all rights reserved. This manual may not be copied, in whole or in part, without the written consent of Integrated Telecom Express, Inc. A300A is a trademark of ITeX. All other product names are trademarks and or registered trademarks of their respective...
Need help?
Do you have a question about the A300A and is the answer not in the manual?
Questions and answers