Table of Contents
Advertisement
Quick Links
Document
HWTP150-TP350_B_HardwareManual_EP
Version
017
Source
Q:\doc\Hardware\HWTP\HWTP150-TP350_B_HardwareManual\
Destination
T:\doc\Hardware\
Owner
mvx
Copyright © 2014
Triamec Motion AG
All rights reserved.
Disclaimer
This document is delivered subject to the following conditions and restrictions:
This document contains proprietary information belonging to Triamec Motion AG. Such information
is supplied solely for the purpose of assisting users of Triamec products.
The text and graphics included in this manual are for the purpose of illustration and reference only.
The specifications on which they are based are subject to change without notice.
Information in this document is subject to change without notice.
TP150/TP350 Power Supplies
Hardware Manual
Triamec Motion AG
Industriestrasse 49
6300 Zug / Switzerland
2014-04-01
+41 41 747 4040
Phone
info@triamec.com
Email
www.triamec.com
Web
Advertisement
Table of Contents
Related Manuals for Triamec TP150
Summary of Contents for Triamec TP150
- Page 1 Disclaimer This document is delivered subject to the following conditions and restrictions: This document contains proprietary information belonging to Triamec Motion AG. Such information is supplied solely for the purpose of assisting users of Triamec products. The text and graphics included in this manual are for the purpose of illustration and reference only.
-
Page 2: Table Of Contents
Table of Contents 1 Safety Information...........................3 2 Product Description..........................4 2.1 Block Diagram..........................5 3 Technical Specifications...........................6 3.1 Environmental conditions........................6 3.2 Electrical Specifications........................7 3.3 AC-Line.............................8 3.4 Discharge Currents...........................8 3.5 EN 61800-5-1...........................8 3.6 EN 61800-3............................8 3.7 Overvoltage............................9 Internal brake capability External brake resistor Overvoltage protection 3.8 LED Diagnostics and Status......................10 3.9 RS232 communication........................10... -
Page 3: Safety Information
The user must have read and understood this documentation before carrying out any operation on Tria- mec Motion AG hardware. Please contact Triamec Motion AG in case of missing information or doubt regarding the installation procedures, safety or any other issue. -
Page 4: Product Description
It is therefore not intended for direct connection to European 3x400VAC power lines. When using the TP150 for TS15x drives, the input must be limited to 1x or 3x110VAC. In a mixed config- uration with TS15x and TS35x drives, the TP150 must be used to ensure correct brake action. -
Page 5: Block Diagram
2.1 Block Diagram Ext. Brake Resistor Fuse with Filter Monitoring Rectifier Galvanic insulation DC/DC Controller DC Bus 2 * Fan RS232 Good Config Figure 1: Block Diagram HWTP150-TP350_B_HardwareManual_EP017 2014-04-01 5/13... -
Page 6: Technical Specifications
3 Technical Specifications 3.1 Environmental conditions Transport and storage conditions During the transport and the storage, the power supply must remain inside their original packaging which complies with the ESD standard. The transport conditions must respect the class 2K3 of the IEC 60721-3-2 standard (temperature between -25°C (-13°F) and +70°C (+158+C), and humidity <95% without condensation) and ... -
Page 7: Electrical Specifications
Caution Mains input voltage drops at maximum load on the Dc-Bus side may break Caution the internal fuse due to capacitor recharging. Consult Triamec on how to avoid this problem. 1 See chapter 3.3 2 Limited by an internal arrestor circuit. -
Page 8: Ac-Line
3.3 AC-Line The power supply must be connected to an electrical network of overvoltage category 3 (refer to EN 61800-5-1 and UL 840 standards for more information) capable of delivering not more than 40kArms, symmetrical amperes (prospective current according to EN 60269-1). -
Page 9: Overvoltage
every power supply, which is to be introduced around the three phase wires of the AC-Line. In some cases it might be beneficial to insert further blocking ferrites ( ) into the DC-Bus pairs. If doing so, make sure, every DC-Bus output of the power supply gets its own ferrite to prevent overheating of the ferrite. Other combinations of motors and cable might require a single stage line EMC filter or an insulated transformer between 3x400V line-in and TP350. -
Page 10: Led Diagnostics And Status
3.8 LED Diagnostics and Status AC-Line DC-Bus Brake Int Brake Ext Status No line power red flash Inrush limiter green green flash Ready green green AC-Line disturbance red flash green Discharging DC-Bus red flash green flash green flash Varistor broken all four LED moving red slow ( 1 per second) Internal brake active green... -
Page 11: Mounting And Wiring
4 Mounting and Wiring The power supply should be protected against any splashes of liquid and any contacts with smoke and dust. It must be installed inside a closed cabinet and mounted as mentioned below. 4.1 Dimensions Dimensions: Width 91 mm Height 205 mm Depth... -
Page 12: Wiring And Connectors
4.5 Wiring and Connectors Mains Ferrite Mains Auto- Supply TPx50 Fuse Switch Transformer DcBusP Drive 1 DcBusN DcBusP Drive 2 DcBusN Ext.-Brake-Res DcBusP BreakN Drive 3 DcBusN BreakP DcBusP Drive 4 DcBusN Fan 1 Fan 2 RS232 Isolation Control Status 24VDC Ground Figure 2: Power Supply Connections... -
Page 13: Warranty Information
All Triamec Motion AG products are warranted for a period of 12 months from the time of installa- tion, or 18 months from time of shipment, whichever comes first. No other warranties, expressed or implied –...
Need help?
Do you have a question about the TP150 and is the answer not in the manual?
Questions and answers