Qdecoder Z2-8 Quick Start Manual

In soft start mode the revs of the motor will be accelerated respectively
decelerated within a quarter second. In this mode one can also control
two-aspect block signals (red/green). The signal lamps of a block signal are
wired to the terminals and
the decoder. The common return wire of the signal must be wired to one of
the blue terminals .
The duration of the run up can be changed in the confi guration variables
CV114 for A0, CV124 for A1, CV134 for A2 and so forth. The switch-off time
is determined by the setting of CV115 for A0, CV125 for A1, CV135 for A2
and so forth.
 Lighting Mode
(programming command 4 )
Each of the outputs A0 through A7
are controlled individually under
separate accessory addresses.
The outputs are confi gured for
continuous mode and are faded in
respectively out within a quarter
second.
command for switching
L1 L2 L3 L4 L5 L6 L7 L8 L9 L10 L11 L12 L13 L14 L15 L16
4 1 2 3 4 5 6
8 5 6 7 8 9 10 11 12
+4
When switching on L9, then L1 is turned off and vice versa.
You can change the addresses of the pairs of lamps under the following CVs:
accessory addresses
lamps L1 and L9
lamps L2 and L10
lamps L3 and L11
lamps L4 and L12
lamps L5 and L13
lamps L6 and L14
lamps L7 and L15
lamps L8 and L16
of a output group A0/A1 through A6/A7 of
L1 L9 L2 L10 L3 L11 L4 L12 L5 L13 L6 L14
A0 A1 A2 A3 A4 A5
7 8 1 2 3 4 5 6
5 6 7 8 9 10 11 12
/
+4
A = CV1 + 256 · CV9
L1,L9
A = CV552 + 256 · CV551
L2,L10
A = CV555 + 256 · CV554
L3,L11
A = CV558 + 256 · CV557
L4,L12
A = CV561 + 256 · CV560
L5,L13
A = CV564 + 256 · CV563
L6,L14
A = CV567 + 256 · CV566
L7,L15
A = CV570 + 256 · CV569
L8,L16
4
© Copyright Qelectronics
These instructions are valid for the
L7 L15 L8 L16
Ex works a Z2 decoder is confi gured for two aspect signals (red/green)
with the (DCC) accessory addresses 1 through 8.
The decoder automatically switches over to Märklin/Motorola, if it
detects a Märklin/Motorola programming command or if CV57 is set to
value "2".
A6 A7
Using the programming button you can confi gure all function outputs of a
Qdecoder
with a single command from your command station.
7 8
You may confi gure the following operating modes of a Z2 with the
programming button:
command
1
1
2
2
3
3
4
4
The number is the accessory address to be entered on the command station.
2)
Press the buttons
GmbH 03/2014
decoder
Quick start guide
Using the Programming Button
to the same mode and determine their accessory addresses
mode
2)
turnout
and motors
without soft start
... with soft start
lighting decoder
respectively as programming commands.
1
Prog
Z2
Qdecoder Z2-8
pulse duration
¼ s
½ s
1 s
2 s
continuous operation