Download Print this page

Advertisement

Quick Links

Overview
This product is a professional wire management system that is linked to your
smartphone. The WMS is designed for operating accessories (including lights, horns,
warning beacons, etc.) typically used on work or off-road vehicles (trucks, jeeps,
ATV/UTV, boats, heavy equipment, farm equipment, etc.).
The unit works on 12V DC and provides output to four terminals which are protected
by a 40A fuse.
Please note that before you can operate this system, you need to download and install
BLAZER LINK app for your smartphone.
Installation
1. Please read these instructions carefully before installing this product. It is
recommended to consult a professional installer to prevent damage to vehicle
and/or system.
2. Do not connect to 24V DC or higher voltage system, as this product is designed for
a 12V DC battery system. In case you have a larger than 12V DC system, check
vehicle owner's manual to determine if a 12V DC output is available and how to
connect in order to use it safely, otherwise, the product will be damaged.
3. Find a suitable flat surface near the battery, clean the surface free of dirt and oil
and then affix the unit using provided adhesive strips and/or mounting holes.
4. Remove the 40A fuse from the holder and disconnect the vehicle battery.
5. Securely attach the positive (red) cable of the WMS unit to the positive terminal of
the battery (or battery cable) and the negative (black) cable of the WMS to the
negative battery cable or chassis.
6. Attach the auxiliary lights/equipment following correct polarity on the terminals and
not exceeding the maximum amperage of the channels (amperage printed on WMS
and corresponds to amperage printed on the remote control for each terminal).
See FIG 1
7. Reconnect battery cables.
8. Insert the 40A fuse back into its holders and snap the cover closed.
Main Unit
CWL623 OWNER'S MANUAL
BLAZER-INTERNATIONAL.COM
1-800-241-3808
Page 1 of 06

Advertisement

loading
Need help?

Need help?

Do you have a question about the CWL623 and is the answer not in the manual?

Questions and answers

Summary of Contents for blazer CWL623

  • Page 1 The unit works on 12V DC and provides output to four terminals which are protected by a 40A fuse. Please note that before you can operate this system, you need to download and install BLAZER LINK app for your smartphone. Installation Main Unit 1.
  • Page 2: App Instructions

    CWL623 OWNER’S MANUAL BLAZER-INTERNATIONAL.COM 1-800-241-3808 App Instructions 9. Download and install BLAZER WMS app for your smartphone operating system. Available on app stores. 10. For initial setup, tap the "radio" icon to go to the "Connect" screen. Simply select the module and enter the appropriate numerical password.
  • Page 3 21. Additional features can be found in the settings tab indicated by the gear icon. b. The Low Voltage Alarm - If the Blazer Link detects that your battery level is lower than the set voltage, it will notify you via the alarm.
  • Page 4: Specifications

    CWL623 OWNER’S MANUAL BLAZER-INTERNATIONAL.COM 1-800-241-3808 Specifications Input low voltage protection 9.5V +/- 0.3V DC 24in Double Row Spot and Flood Page 4 of 06...
  • Page 5: Troubleshooting

    CWL623 OWNER’S MANUAL BLAZER-INTERNATIONAL.COM 1-800-241-3808 Troubleshooting 1. Wires not connected properly in the terminals Auxiliary lights/equipment not operational. 2. If the contacts don’t open, gently push downwards on the screws 3. App on smartphone not connected (paired) to the main unit. Reconnect 4.
  • Page 6 CWL623 OWNER’S MANUAL BLAZER-INTERNATIONAL.COM 1-800-241-3808 changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two...