1. Manuals
  2. Brands
  3. DieHard Manuals
  4. Battery Charger
  5. 200.71233
  6. Owner's manual

DieHard 200.71233 Owner's Manual

Battery charger 50/15/2 amp manual engine starter with battery tester and air compressor 225/125 amp
Hide thumbs Also See for 200.71233:
Table of Contents

Advertisement

Quick Links

Download this manual
OWNER'S MANUAL
®
BATTERY CHARGER
50/15/2 Amp
Manual
ENGINE STARTER
With Battery Tester and
Air Compressor
225/125 Amp
Model No.
200.71233
CAUTION:
Read all Safety Rules and Operating Instructions,
and follow them with each use of this product.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
00-99-000538/0506

Advertisement

Table of Contents
loading

Related Manuals for DieHard 200.71233

Summary of Contents for DieHard 200.71233

  • Page 1 ENGINE STARTER With Battery Tester and Air Compressor 225/125 Amp Model No. 200.71233 CAUTION: Read all Safety Rules and Operating Instructions, and follow them with each use of this product. Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. 00-99-000538/0506...

  • Page 2: Table Of Contents

    Warranty THREE-YEAR FULL WARRANTY If this Battery Charger fails due to a defect in material or workmanship within three years from the date of purchase, RETURN IT TO ANY SEARS STORE or OTHER DIEHARD OUTLET IN THE UNITED STATES FOR FREE REPLACEMENT.

  • Page 3: Important Safety Instructions

    – SAVE THESE INSTRUCTIONS – To reduce the risk of explosion, explosive gases, or injury while using your battery charger, follow the precautions listed below: • Do not disassemble charger. Take it to a qualified service professional if service or repair is required.

  • Page 4: Parts

    Parts This section shows an illustration of your battery charger. Use it to become familiar with where all the parts are located, and what they look like. Replacement Parts List DieHard 71233 ITEM DESCRIPTION Handle Positive (RED) Cable w/clamps Negative (BLACK) Cable w/clamps...

  • Page 5: Before Using Your Battery Charger

    Before Using Your Battery Charger It is important to prepare your charger for use. This section will tell you how to assemble the charger, ground and connect the power cord, and prepare to charge a battery. Assembling your charger It is important to fully assemble your charger before use.

  • Page 6: Plugging It In

    Axle Assembly (continued) Place the charger on its side. Place one end of each bracket into slot, then place the axle assembly under each bracket. Fasten the other side of each bracket using the two, 10-32 thread cutting screws provided. Handle: Turn the charger right side up onto its foot and wheels.

  • Page 7: Using An Extension Cord

    Using an extension cord The use of an extension cord is not recommended. If you must use an extension cord, please make sure that you follow these guidelines: • Make sure the pins on the plug of the extension cord are the same number, size, and shape as those of the plug on the charger.

  • Page 8: Using Your Battery Charger

    Using Your Battery Charger To obtain the best results from your battery charger, you must know how to use it properly. This section tells how to set the controls and how to charge a battery in and out of the vehicle.
  • Page 9 2. Press the DISPLAY MODE button so the VOLT- AGE LED lights. 3-WAY SWITCH 3. Connect the battery charger as outlined in “Charg- ing Your Battery” on page 10. The voltage will be displayed. NOTE: If a battery has recently been charged or in a vehicle that has been run recently, turn on the vehicle’s headlights for a few minutes before...

  • Page 10: Using The Compressor

    Using the compressor CAUTION – Read instructions of the product being inflated before using the compressor. Avoid over inflation, do not exceed the manufacturer’s recom- mended pressures. Do not leave the air compressor unattended during use. NOTE: The 12 volt compressor is rated for 120 PSI. The compressor will not start at pressure greater than 80 PSI.

  • Page 11: Charging Your Battery

    12. Facing away from the battery, remove the charger clamps in this order: (1) from the vehicle chassis or engine block (2) from the battery post or terminal. 13. Clean and store the battery charger in a dry location.
  • Page 12 OFF. Unplug the charger power cord from the wall outlet. 11. Face away from battery and remove the charger clamps from the NEGATIVE end of the cable first, then from the POSITIVE post. 12. Clean and store the battery charger.

  • Page 13: Calculating Charge Times

    Calculating charge times The Chart Method Use the following table to more accurately determine the time it will take to bring a battery to full charge. First, identify where your battery fits into the chart. • Small batteries — motorcycles, garden tractors, etc. —...

  • Page 14: Troubleshooting

    BUTTON options are selected correctly. Continue to charge battery for another two hours. If problem continues, call Sears Service at 1-800-SEARS 64. Circuit breaker cycles when current draw is too high. Separate the clamps. Check for worn cables and replace if needed.
  • Page 15 For information about troubleshooting, call toll-free from anywhere in the U.S.A. 7 am to 4:30 pm Central Time Monday through Friday. 1-800-SEARS-64 (1-800-732-7764).

Table of Contents