1. Manuals
  2. Brands
  3. Yunlink Manuals
  4. Wireless Access Point
  5. CPE150-P24
  6. User manual

Yunlink CPE150-P24 User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Test Model：CPE150-P24
User Manual
This is the user manual of Outdoor WiFi Bridge with Qualcomm Chipset, which will approximate guide you how to set
and apply this product. It provide a convenient graphical interface for network construction and maintenance person,
as well as a user through a simple and accurate operation, and configuration management of the ceiling wireless
access point.
1

Advertisement

Table of Contents
loading

Related Manuals for Yunlink CPE150-P24

Summary of Contents for Yunlink CPE150-P24

  • Page 1 Test Model：CPE150-P24 User Manual This is the user manual of Outdoor WiFi Bridge with Qualcomm Chipset, which will approximate guide you how to set and apply this product. It provide a convenient graphical interface for network construction and maintenance person, as well as a user through a simple and accurate operation, and configuration management of the ceiling wireless access point.
  • Page 2 Attention: 1. Check box contents: Outdoor CPE PoE Power adapter (for 24V Passive PoE device) LAN cable User Manual Installation Accessory 2. Warning:  Do not use the same power source for the product as other equipment, Only use the power adapter that comes with the package.

  • Page 3: Table Of Contents

    Contents Chapter 1: Hardware and Operation mode Instruction……………..…………...…………..……….4 1.1 Interface Instruction..……………..……………………..........………4 1.2: LED light instruction…………..……………………............4 1.3 PoE Power Connection and Installation………………............4 Chapter 2: Working Diagram………………....................5 Chapter 3: WDS Switch Button Configuration………………..............5 Chapter 4: WEB GUI Login………………....................9 Chapter 5 : WEB GUI interface Setting……...................11 5.

  • Page 4: Chapter 1: Hardware And Operation Mode Instruction

    Chapter 1: Hardware and Operation mode Instruction 1.1 Interface Instruction: P1 Product Interface LAN: 1*10/100Mbps RJ45 port, can support 24V Passive PoE. WAN: 1*10/100Mbps RJ45 port, can support 24V Passive PoE, but it change to LAN port under WDS, WiFi Repeater operation mode RST: Reset Button, press 10~15 seconds, outdoor CPE will revert to default settings.

  • Page 5: Poe Power Connection And Installation

    1.3 PoE Power Connection and Installation There is a PoE adapter and Installation Accessory in the box, then pls install and power the outdoor CPE as following pictures: P2 Power Connection and Installation Chapter 2: Working Diagram Then outdoor CPE with panel antenna, mostly for Point to Point and Point to multi Point connections. Take outdoor CPE work with IP camera for example to show the working diagram: A.
  • Page 6 B. PTP Working Diagram of Outdoor CPE work with Multiple IP Camera: P4: Working diagram C. PTMP Working Diagram of Outdoor CPE work with IP Camera: P5: Working diagram D. PTMP Working Diagram of Outdoor CPE work with Multiple IP Camera: P6: Working diagram...

  • Page 7: Chapter 3: Wds Switch Button Configuration

    E. PTP Working Diagram of Outdoor CPE applied to Wireless Coverage: P7: Working diagram Chapter 3: WDS Switch Button Configuration This Outdoor CPE support Wireless AP, Gateway, WISP, Wireless Bridge, WDS operation mode, effective solution for PTP, PTMP application and outdoor long range wifi coverage application. What’s more, there is WDS button on the case, easy to do PTP,PTMP connection by press the WDS button and reset button, no need to access into product GUI.
  • Page 8 Remark: The master AP can connect with 1~4 slave AP The WDS switch button in S side in default The default IP address of master AP and slave AP is 192.168.288.253. Operation: : Power on the Master AP and Slave AP; : Push the WDS switch button to M side on Master AP, Master AP’s IP address will change to 192.168.188.252.

  • Page 9: Chapter 4: Web Gui Login

    P11: LED Light Status If there are 2~4 Slave APs, the 4 steps will change to as follow: Press the reset button around 1 second on the 2nd slave AP, 3rd slave AP, 4th slave AP, and finish this step in 2 mins, then all slave AP will connect with master AP automatically;...
  • Page 10 P12 Setting of computer’s IP address P13 Setting of computer’s IP address Input 192.168.188.253 into IE browser, then pop up the login page, there are user/admin login page, input admin to login the user page; or input root to login the admin page.

  • Page 11: Chapter 5 : Web Gui Interface Setting

    P14 Login Pls note, In user page, mainly to introduce the WDS operation mode, but in admin page, mainly to introduce wireless AP, Gateway, WiFi Repeater, WISP, WDS operation mode. Chapter 5 : WEB GUI interface Setting: 5. 1 User Login Page: After Login in the user, then will pop up the CPE working status picture showed as follow: In this page, show the AP’s default operation mode, channel, end user QTY, connection status, CPU usage status, Wireless, LAN and AP location info.

  • Page 12: Wireless Setting

    P15: Device Status 5.1.1 Wireless Setting The default is wireless off, if need wireless on, GUI configuration page showed as below: Click 2.4G, will pop up following window, click wireless status to enable wireless. P16: Wireless Settings User can configure the SSID, password, bandwidth, channel in the above picture, then Apply to finish.

  • Page 13: Lan Setting

    P17. Wireless setting 5.1.2 LAN Setting To setup the outdoor CPE’s management IP address, configure the DHCP or Fix IP P18 LAN Setting 5.1.3 Super WDS Settings In super WDS settings, it mean the outdoor CPE will do the WDS operation mode. Click Super WDS settings, will pop up following picture: Config the SSID, Channel, Bandwidth, location for the master wireless AP, then input the slave wireless AP’s MAC address, max can banding with 4PCS slave wireless AP, click next to finish and waiting the data saving.
  • Page 14 P19 Super WDS Setting Pls note, to make the master AP work in best channel, user can use the wireless analyzer, to choose the channel that with small wireless AP.

  • Page 15: Wizard

    P20 wireless analyzer 4.1.4 Wizard In Wizard, it is same configuration of 4.1.3: Super WDS settings 4.1.5 Advanced Will show more in 4.2 4.2 Admin Login In admin page, the status is almost same as the user page; Can check 4.1 user login for more details; P21 Admin Status 5.2.1: Wizard In admin login, and in Wizard, there are gateway, repeater, WISP, AP and Super WDS operation mode, Please confirm...

  • Page 16: Gateway Mode

    P22 Operation mode 5.2.1.1 Gateway Mode: Before Click Gateway mode, confirm your internet will be static IP, PPPoE, or DHCP: Then will pop up following picture after click it, Please choose the right WAN setting mode, then click next to continue. P23.
  • Page 17 P24 Wireless Setting in Gateway Mode Please not: to make the outdoor CPE work in some clear channel, user can click wireless analyzer at first. Less AP in the channel, then Wireless performance will be more stable. Picture showed as below: P25 Channel Analysis When click Next, then will complete the Gateway mode setting and show following picture:...

  • Page 18: Wifi Repeater Mode

    Complete the setting in Gateway Mode When return to Status, will show wireless router’s SSID, internet connection, LAN connection status showed as follow: P27 Status in Gateway Mode 5.2.1.2 WiFi Repeater mode A. Login the Web management page, click “Wizard”, then “WiFi Repeater” B.
  • Page 19 P28 Repeater Mode Click Return button, will back to Status, show Repeater mode data, show fail or success, and user can configure this data in this page if required. P29 Status in Repeater Mode In wifi repeater operation mode, the default is SSID disable. If want to enable SSID, then click Wireless Setting.

  • Page 20: Wisp Operation Mode

    P30 Wireless Setting 5.2.1.3 WISP Operation mode: Click WISP operation mode in Wizard, then will pop up the configure page, pls set the WISP operation mode based on the steps showed in picture: P31 WISP Mode Configure the right WAN setting in WISP operation mode, then next to complete...
  • Page 21 P32 WAN setting in WISP mode Then complete and back to status, will show the connection fail or success, then can configure the data based on request: P33 Status in WISP mode Remark: When click WAN Setting, will pop up following picture to ask you choose PPPoE, DHCP or Static IP...

  • Page 22: Ap Operation Mode

    P34 WAN setting in WISP mode 5.2.1.4 AP Operation mode: Set the wireless data, AP Location info as required, then click next to continue and enter into LAN setting. After LAN setting, complete the AP mode configuration and back to Status: P35 Wireless setting in AP Mode...

  • Page 23: Super Wds Mode

    P36 LAN Setting in AP Mode P37 Status in AP Mode 5.2.1.5 Super WDS mode: In this part, pls refer to 4.1 Part. 5.3 Advanced Setting: In advanced setting, mainly for outdoor CPE’s device status, wireless setting, Networking setting and management...

  • Page 24: Device Status

    configuration. Let’s Click Advanced Setting in status page, will show return home, Setup Wizard which we showed in the advance chapters. Let’s shown more in Device Status, Wireless, Network and Management in following pages: 5.3.1 Device Status This part to show the outdoor CPE’s status, Wireless Status and LAN status. In status, mainly to check the ceiling outdoor CPE’s firmware version, hardware version, uptime info.: P38 Device Status In wireless status, to show outdoor CPE’s SSID, MAC address for WiFi, Channel, Encryption, Client List info.

  • Page 25: 2Wireless

    following picture. P40 LAN Status 5.3.2: Wireless: For wireless, mainly to configure the wireless SSID, password, encryption, channel, Multi SSID, tag VLAN, RF power adjust from Basic Setting, Virtual AP, Access control and Advanced Setting: Basic Settins: To configure WDS outdoor CPE’s SSID, channel, bandwidth, MAC address and Encryption P41 Basic Setting in Wireless Virtual AP: There are 3 virtual AP in 2.4G wireless, if need do multi SSID, then users can configure it showed in following picture:...
  • Page 26 P42 Virtual AP Access Control: Allow or deny the users access into this wireless AP based on MAC address P43 MAC Access Control Advanced Settings: In this page, will show the regional, mode, RF Power, Max user access... Remark: In Regional, the default is Debug, which including the frequency of 2.312GHz to 2.4835GHz, but some local laws will prohibit this, so, pls strictly abide by local laws and by cautious in using them.

  • Page 27: Network Setting

    P44 Advanced Setting 5.3.3 Network: In network, mainly to show the LAN setting and tag VLAN as follow: In LAN Settings, mainly including static IP and DHCP. P45 Network Setting...

  • Page 28: Management

    In VLAN part, need an VLAN switch and make sure the multi SSID is enable, then input the VLAN ID to different SSID. P46 Tag VLAN Setting 5.3.4 Management: In this part, show the system time, Logs, upgrade firmware, system, user info. And we show System time, how to upgrade firmware and system page to users: P47 System Time In this part, there is signal tracking tool, which will track the wireless signal, and show the signal strength.
  • Page 29 P48 Signal Tracking Logs to show the outdoor CPE’s operation logs, useful for problem solved. P49 Signal Tracking In firmware upgrade page, pls make sure to tick Restore factory settings after firmware upgrade.
  • Page 30 P50 Firmware Upgrade In System, this is for firmware backup or restor, or reset to default. Or reboot, mostly for problem solve. P51 System info User: user can change the login password based on their needs: P52 User...

  • Page 31: Chapter 6 Share Internet And Obtain Ip Address Automatically

    Chapter 6 Share Internet and Obtain IP address automatically Set computer’s TPC/IP as Obtain an IP address automatically, Obtain DNS server address automatically as following picture showed. the computer will obtain the IP address from router or base station to get Internet.

  • Page 32: Chapter 7 Trouble Shooting

    Chapter 7: Trouble Shooting: F 1 The Failure phenomenon and solution Failure phenomenon Solution Pls make sure the PoE module connection is right. POE Port connect SYS Indicator off with AP, LAN port connect with computer Pls check the IP address of computer and Wireless AP to see whether they are in same networking segment, The method is click “start”-“Run”...

Table of Contents