Advertisement
Wierless Settings
This part is valid for wireless se ngs only
①Defaults Parameter
The default se ng allows the scanner to be restored
to the factory se ng state.
Set up process：
❶Scan the bar code of"Enter Setting".
Enter Se ng
❷Scan the bar code of "Restore Defaults".
Restore Defaults
❸Scan the bar code of "Exit and Save".
Exit and Save
②Numeric Keypad
Configura on method: Scan the func on bar code directly.
Enable Numeric Keypad
*Disable Numeric Keypad
Decode Settings
This part is valid for decode se ngs only
Se ng Step
Scan the bar code of "Enter se ng"
1
Enter Se ng
2
Scan the func on bar codes
Scan the bar code of "Exit and Save"
3
Exit and Save
③ Suffix
Set up process：
❶Scan the bar code of"Enter Setting".
Enter Se ng
❷Scan the bar code of "Custom Suffix".
Custom Suffix
❸Scan one of bar code below as suffix
None
*0x0D （CR）
0x0A （LF）
TAB
❹Scan the bar code of "Exit and Save".
Exit and Save
① Trigger Mode
Single decode
: When a bar code has been decoded, the reader will
be turned off. The reader must be triggered again to read another
label.
Con nuous decode
: The reader will produce as much data as it
can decode regardless whether it is the same or not. This mode is
mainly used for demonstra on and diagnosis.
*Single Read
Con nuous Read
② Reading Mode
Disable repeat read（F0100）
*Enable repeat read （F0101）
Mul ple read（F0102）
Mul ple read: The same label can only be decoded again a er
the label has not been detected for a number of
scans. This mode can only be programmed in
Con nuous read trigger mode.
④Sleep Time Setting
The sleep me means the me between the last opera on move and
auto turn off the scanner. User able to scan the corresponding bar code
of the sleep me which is needed to accomplish the sleep me se ng.
Set up process：
❶Scan the bar code of"Sleep Time".
Sleep Time
❷Scan one of the bar code below as sleep me.
20S
60s
3min
5min
15min
30min
None sleep
❸Scan the bar code of "Exit and Save".
Exit and Save
③ Dalay for repeating to
read the same barcode
500ms（F0205）
1000ms（F0210）
2000ms（F0220）
④ Auto trigger（optional）
Disable auto trigger（H0000）
* Enable auto trigger（H0001）
Light
LED Status
Descrip on
Scanner
Green light on
Power on/ Working normally
Red light blinks
Pairing match
Green light blinks once
Upload successfully
Green light blinks twice
Upload failed
Red light on
Low ba ery
Blue light on
Charging normal
Green light on
Charging complete
Green light blinking
Pairing unsuccessful
Cradle
Green light blinks 30s
Pairing state
Red light on
USB iden fy failed
Green light blinks once
Uploaded successfully
Green light on
Working normally
FCC STATEMENT :
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired
operation.
Warning:
Changes or modifications not expressly
approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE:
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
Advertisement
