Subscribe to Our Youtube Channel
Related Manuals for Ventrac ET200
Summary of Contents for Ventrac ET200
- Page 1 OWNER/OPERATOR’S MAN UAL & PARTS LIST ET200 TURBINE BLOWER Re vised 10/23/14 09.10006...
- Page 2 TO THE OWNER Product Identification If you need to contact an Authorized Ventrac Dealer for information on servicing your product, always provide the Product Model and Serial numbers. Please fill in the following information for future reference. See picture below to find the location of the identification number.
-
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION SECTION A Description and Specifications ......A-1 SAFETY SECTION B Safety Symbols . - Page 4 Product Description ET200 Turbine Blower The ET200 Turbine Blower is designed to blow a large volume of air using a radial fin turbine design. Because of this design, the Turbine blower is much quieter than a conventional leaf blower. It can be used effectively to blow leaves, light snow, and debris from sidewalks, parking lots and other areas requiring debris removal.
- Page 5 SAFETY ATTENTION This symbol identifies potential health and safety hazards. It marks safety precautions. Your safety and the safety of others is involved. SIGNAL WORD DEFINITIONS Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. This signal word is limited to the most extreme cases.
- Page 6 SAFETY The following decals must be maintained on your Ventrac turbine blower. If any decals are faded or missing, contact your dealer promptly for replacements.
-
Page 7: Safety
SAFETY Page & Decal Description Part Number Location E-1, #29 Danger - Shield Missing 00.0062 E-1, #36 Warning - Do Not Reach 00.0219 E-3, #26 E-3, #16 (2) Warning Moving Parts 00.0216 E-3, #23 Read Owners Manual 00.0217 E-3, #24 General Safety 00.0220 E-7, #17... -
Page 8: General Safety Procedures
SAFETY General Safety Procedures for Ventrac Tractors, Attachments, & Accessories Read and understand the operator’s manual before operating this equipment. Observe and follow all safety decals. DO NOT let children or any untrained person operate the tractor or attachment. Make sure that all operators of this equipment are thoroughly trained in using it safely. - Page 9 SAFETY ET200 Safety Procedures Before making any repairs or adjustments, lower attachment to the ground, set parking brake, shut the engine off, and remove the key. Read and understand the operator’s manual before operating this equipment. • Read and understand the owner’s manual before attempting to operate this machine.
-
Page 10: Attaching
OPERATION Operating Instructions Attaching: 1. Drive the tractor forward slowly into the hitch arms on the turbine blower. Align the hitch arms of the tractor with the hitch arms on the blower by raising or lowering the tractor hitch arms. Because the blower is resting on a castor wheel and may roll away from the tractor, it may be necessary to manually push it onto the tractor hitch arms to complete the engagement. -
Page 11: Operating Tips
OPERATION USE CAUTION WHEN OPERATING NEAR OBJECTS WHICH MAY ROLL OR TIP FROM THE HIGH WIND VELOCITY OF THE BLOWER, SUCH OBJECTS CAN CRUSH OR INJURE PERSONS OR PETS. FLYING DEBRIS CAN ALSO CAUSE INJURY TO PERSONS AND DAMAGE TO BUILDINGS, AUTOS, ETC. -
Page 12: Maintenance/Adjustments
MAINTENANCE/ADJUSTMENTS Daily: • Check for any signs of loose bolts and nuts, tighten as needed. • Visually inspect both the inlet and outlet areas for foreign objects and/or material. • Visually inspect the fins of the turbine blower fan and the inside of the blower housing for buildup of dirt or dust. -
Page 13: Maintenance
MAINTENANCE/ADJUSTMENTS Belt Adjustment: Before making any repairs or adjustments, lower attachment to the ground, set parking brake, shut the engine off, and remove the key. • To adjust turbine drive belt, remove the inlet screen (page E-3, ref 25) and increase the spring tension on the idler arm by hooking the torsion spring leg (page E-1, ref 2) in the next notch down. -
Page 14: Main Frame & Blower Drive
PARTS ILLUSTRATED DRAWING MAIN FRAME & BLOWER DRIVE... - Page 15 28 ..00.0189 ... DE CAL, VENTRAC OR BITAL ....
-
Page 16: Shields, Stand, & Wheel Mount
PARTS ILLUSTRATED DRAWING SHIELDS, STAND, & WHEEL MOUNT... - Page 17 18 ..62.1391 ... STAND, ET200 .....
-
Page 18: Hydraulic Motor
PARTS ILLUSTRATED DRAWING HYDRAULIC MOTOR... - Page 19 PARTS HYDRAULIC MOTOR REF. PART NO. DESCRIPTION QTY. 1 ..81.AX56 ... BELT, AX56 ......1 2 .
-
Page 20: Blower Mount & Discharge Nozzle
PARTS ILLUSTRATED DRAWING BLOWER MOUNT & DISCHARGE NOZZLE... - Page 21 PARTS BLOWER MOUNT & DISCHARGE NOZZLE REF. PART NO. DESCRIPTION QTY. 1 ..90.0612 ... BOLT, 3/8-16 USS X 1 1/2 ..... 9 2 .
- Page 22 Tractors & Attachments used Commercially or for any income producing purpose is limited to Two (2) years from original purchase date. Ventrac ET200 turbine blower (turbine only) is limited to Two (2) years from original purchase date. Ventrac HG100/HG150 generator is limited to One (1) year from original purchase date.
- Page 23 (i) damage or defects due to or arising out of repair of Ventrac turf equipment by person or persons other than an authorized Ventrac service dealer or the installation of parts other than genuine Ventrac parts or Ventrac recommended parts.
Need help?
Do you have a question about the ET200 and is the answer not in the manual?
Questions and answers