Download
Share
Print this page
  1. Manuals
  2. Brands
  3. ICON Manuals
  4. Automobile Parts
  5. 54000T
  6. Installation instructions

ICON 54000T Installation Instructions

2007-up fj/4runner tubular lower trailing arm kit
Hide thumbs
1
2
3

Advertisement

Quick Links

Download this manual
7929 Lincoln Ave. Riverside, CA 92504
Phone: 951.689.ICON
Fax: 951.689.1016
COMPONENTS INCLUDED
(1) 154400 07-UP FJ/4RUNNER TUBULAR LOWER
TRAILING ARM (DRVR)
HARDWARE INCLUDED
(2) 127005 HEIM SPACER JM16 X .570 X 2.625
(2) 157430 HEIM SPACER JM16 X .570 X 2.075
(2) 295510 JM16-1T 1-14 RH ROD END F1 FIT

TOOLS REQUIRED

JACK
JACK STANDS
TORQUE WRENCH
TECH NOTES
1. DO NOT EXCEED 3.5" FROM LINK FACE TO CENTERLINE OF ROD END.
2. BUSHINGS ARE GREASELESS AND DO NOT REQUIRE MAINTENANCE.
3. LOWER ARMS MOUNT SO THAT THE REAR BUSHING HOUSING IS TANGENT WITH THE TUBE ON
BOTTOM. IF MOUNTED UPSIDE DOWN, LINK TUBE WILL BIND ON AXLE HOUSING.
INSTALLATION
1.
Using a properly rated jack, raise the rear of the vehicle and support the frame rails with jack stands. Ensure the jack stands are
secure and set properly before lowering the jack. NEVER WORK UNDER AN UNSUPPORTED VEHICLE. Remove the rear wheels
NOTE: REMOVE AND REPLACE ONLY ONE FACTORY LINK ARM AT A TIME.
2
. Lay ICON link arm over the factory link to set a starting point for adjustment (26.75").
3
. Use the factory hardware to install the link arm on the axle end using a 19mm socket/wrench. [Torque to factory spec]
[FIGURE 1 & 2]
FIG.1
PART #
54000T
(1) 154401 07-UP FJ/4-RUNNER TUBULAR LOWER
TRAILING ARM (PASS)
(2) 297102 GREASELESS PRESS IN BUSH 2.135 X
14.3MM X 58.85MM
(2) 605920 1-14 JAM NUT
1.5" OPEN END WRENCH
12MM SOCKET / WRENCH
19MM SOCKET / WRENCH
21MM SOCKET / WRENCH
54000T INSTALLATION INSTRUCTIONS
DESCRIPTION
2007-UP FJ/4RUNNER TUBULAR LOWER
TRAILING ARM KIT
WARNING!
** READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH
BEFORE BEGINNING INSTALLATION! IF THESE INSTRUCTIONS ARE
NOT PROPERLY FOLLOWED SEVERE FRAME, SUSPENSION AND TIRE
DAMAGE MAY RESULT TO THE VEHICLE!
** ICON VEHICLE DYNAMICS RECOMMENDS THAT YOU EXERCISE
EXTREME CAUTION WHEN WORKING UNDER A VEHICLE THAT IS
SUPPORTED WITH JACK STANDS.
** ICON VEHICLE DYNAMICS RECOMMENDS ALL INSTALLTION TO
BE PERFORMED BY A PROFESSIONAL SHOP/SERVICE TECHNICIAN.
PRODUCT FAILURE CAUSED BY IMPROPER INSTALLATION WILL NOT BE
COVERED UNDER ICON'S WARRANTY POLICY.
6-01-2016 REV.A
FIG.2
1

Advertisement

loading

Related Manuals for ICON 54000T

Summary of Contents for ICON 54000T

  • Page 1: Tools Required

    NOTE: REMOVE AND REPLACE ONLY ONE FACTORY LINK ARM AT A TIME. . Lay ICON link arm over the factory link to set a starting point for adjustment (26.75”). . Use the factory hardware to install the link arm on the axle end using a 19mm socket/wrench. [Torque to factory spec] [FIGURE 1 &...
  • Page 2 . The pinion angle can be adjusted as desired once both links are installed. Do not adjust longer than 3.5”. [FIGURE 3] FIG.3 . Connect the link to the frame using the factory hardware with the short spacer towards the inside of the vehicle. This will move the front link pivot points closer together on the frame to help correct roll-steer geometry on lifted vehicles.
  • Page 3 ICON VEHICLE DYNAMICS LIMITED LIFETIME WARRANTY ICON Vehicle Dynamics warrants to the original retail purchaser who owns the vehicle on which the product was originally installed. ICON Vehicle Dynamics does not warrant the product for finish, alterations, modifications and/or installation contrary to ICON Vehicle Dynamics instructions.