Sno-Way 99101220 Installation & Owner's Manual

Skid steer snow plow

Advertisement

Quick Links

INSTALLATION &
OWNER'S MANUAL
29VSKD SERIES
SKID STEER SNOW PLOW
99101237 & 99101220
WITH SERIAL NUMBERS AFTER:
29VSKD200000
®
Sno-Way
Is a registered trademark of Sno-Way International, Inc.
V-Wing
and MaxAdjust
are trademarks of Sno-Way International, Inc.
®
©2015 Sno-Way
International
97101982A

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 99101220 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Sno-Way 99101220

  • Page 1 OWNER’S MANUAL 29VSKD SERIES SKID STEER SNOW PLOW 99101237 & 99101220 WITH SERIAL NUMBERS AFTER: 29VSKD200000 ® Sno-Way Is a registered trademark of Sno-Way International, Inc. ™ ™ V-Wing and MaxAdjust are trademarks of Sno-Way International, Inc. ® ©2015 Sno-Way...
  • Page 2: Table Of Contents

    TABLE OF CONTENTS Page INTRODUCTION ......................2 SAFETY ........................3 THEORY OF OPERATION..................4 General ......................4 Plow Operational Limits ................... 4 Skid Steer Power Unit..................4 Skid Steer V-Plow Hydraulic System .............. 4 PLOWING OPERATION....................5 Before The Season Begins ................5 Transporting Vehicle With Plow Attached ............
  • Page 3: Introduction

    This manual was written for the assembly, installation and BE AWARE! It is illegal to remove, deface or other- maintenance of your new Sno-Way Skid Steer V-Snow wise alter the safety decals mounted on this equip- Plow. Most importantly, this manual provides an operating ment.
  • Page 4: Safety

    An incorrect plow position blocking headlamp decals are in place and are legible before operation beam may result in an accident. begins. New decals can be obtained from Sno-Way or ALWAYS check surrounding area for hazardous your local dealer.
  • Page 5: Theory Of Operation

    THEORY OF OPERATION General Skid Steer V-Plow Hydraulic System The Sno-Way Skid Loader V-Plow is mounted using a The auxiliary hydraulics are routed to the valve block universal mounting plate. The V-Plow pressure and return where the hydraulic fluid is diverted for wing functions. To...
  • Page 6: Plowing Operation

    PLOWING OPERATION Before The Season Begins Plowing Like A Pro 1. Inspect vehicle safety equipment for proper operation; brakes, headlights, plowing lights, windshield WARNING wipers, flashers, etc. 2. Inspect the plow, plow frame and all attaching • Never exceed 10 mph when plowing! Serious hardware for wear and corrosion.
  • Page 7: Troubleshooting Guide

    One of the auxilliarly power lines is disconnected but not retract Wings will not collaspe when hitting Case drain line disconnected an object When wings hits an object the other Case drain line disconnected wing extends FOR ANY OTHER ISSUE, CHECK WITH YOUR SNO-WAY DEALER...
  • Page 8: Maintenance

    MAINTENANCE General Fluid Compatibility • Before operating, perform a thorough visual Hydraulic fluid used in skid steers is compatible with the inspection of the equipment. Look for fluid leaks, plow system. cracked, bent or broken components, loose nuts, bolts or attachments and proper fluid levels. Special Fasteners Torques and •...
  • Page 9: Installation

    INSTALLATION Control Wiring Installation 1. Position the control box in cab. Secure the control box CONTROL using hook and loop fastener provided. HARNESS 2. Route the power harness lead to the battery (See CONTROL Figure 1-4). Connect the YELLOW wire to the negative (- ) battery terminal and the WHITE wire to the positive (+) battery terminal.
  • Page 10 4. Position the drivers side (DS) and passenger side 8. Install the center shield on the clevis pin retainer (PS) wings in front of the A-frame/tower assembly. (See bracket, and secure with two 5/16-18 x 1’’ hex head cap Figure 1-6) screws (p/n 98009149), four 5/16"...
  • Page 11: Mounting Snow Plow To Vehicle

    10. Attach a plow marker to each wing as shown and 13. Adjust each hose length from clamps to hose end secure using 5/16" x 1" cap screws and locknuts. (See fittings to 33 in. and tighten both clamp screws. (See Figure 1-10) Figure 1-12) NOTE: If installing screw with an impact wrench, ensure...
  • Page 12: Removing Snow Plow From Vehicle

    Adjust the plow shoes as follows: Removing Snow Plow From Vehicle a. Park the vehicle on a smooth level surface. Adjust 1. Lower the snow plow to the ground. the wings straight out on each side and lower the 2. Disconnect the hydraulic hoses and electric plow to the ground.
  • Page 13: Trip Spring Adjustment

    4. Loosen the lower jam nut on each eyebolt. (See f. After the disk shoe position is properly adjusted Figure 1-16). place washers on the shoe stem - above the plow frame and below the retaining lynch pin - to remove all up and down movement of the disk shoe in the frame.
  • Page 14: Wiring Schematic

    WIRING SCHEMATIC...
  • Page 15: Hydraulic Schematic

    HYDRAULIC SCHEMATIC PLOW SWITCH CYLINDER FLOW FLOW FUNCTION POSITION PRESSURIZED SOLENOID SOLENOID INLET TO TANK PORT STATUS STATUS NEUTRAL MIDDLE - OFF LEFT EXTEND LEFT LEFT RETRACT LEFT RIGHT EXTEND RIGHT RIGHT RETRACT RIGHT...
  • Page 16: Torque Specifications

    TORQUE SPECIFICATIONS 1 or 2 Grade No Marks and Head Markings Grade No Marks and Nut Markings Grade 1 Grade 2 Grade 5, 5.1 or 5.2 Grade 8 or 8.2 Lubricated Lubricated Lubricated Lubricated SIZE lb-ft lb-ft lb-ft lb-ft lb-ft lb-ft lb-ft lb-ft...
  • Page 17 NOTES...
  • Page 18 ® SNO-WAY INTERNATIONAL, INC. Hartford, WI 53027 USA Website: www.snoway.com © ® 2015 Sno-Way International...
  • Page 20 Fill out Warranty Registration Card and mail COPY 1 to the factory to validate Warranty. NO Warranty claims can be honored if the Warranty Card is not on file at the factory. ® SNO-WAY INTERNATIONAL, INC. Hartford, WI 53027 USA Website: www.snoway.com © ® 2015 Sno-Way International...

This manual is also suitable for:

29vskd series99101237

Table of Contents