Advertisement
Advertisement
Related Manuals for Motorline professional mbm6
Summary of Contents for Motorline professional mbm6
- Page 1 MBM6 - Barrier Installer and User’s manual v2.0 REV. 11/2013...
-
Page 2: Table Of Contents
CONTENT SAFETY INSTRUCTIONS INDEX STANDARDS TO FOLLOW 00. CONTENT ATTENTION: index | page 01.A To ensure the safety of people, it is important that you read all the following 01. SAFETY INSTRUCTIONS instructions.Incorrect installation or incorrect use of the product can cause physical standards to follow | page 01.B injury and material damage. -
Page 3: Package
Working frequency metal plate 3 - 6 s Opening / Closing time 3 - 6 s MC15 Boom control board cover The main dimensions of the MBM6 barrier are: MX4SP 53 mm transmitter Electromechanical barrier photocells 100 mm Fastening metal plates... -
Page 4: Operator
WARNING LIGHT LOCKING / UNLOCKING The MBM6 barrier is a product developed with the purpose of controlling the access of In case of power failure, the barrier is equipped with a manual unlocking and locking vehicles to private, industrial and commercial areas. -
Page 5: Installation Site Preparation | Page 04.A
INSTALLATION INSTALLATION INSTALLATION SITE PREPARATION BARRIER’S FIXATION 1 With the bolts already fixed on the It’s important that this order of installation is respected! cement foundation, respecting the Otherwise we can’t assure the correct installation of the barrier and it may dimensions of point 2, place the barrier on not work properly. - Page 6 INSTALLATION INSTALLATION BOOM ASSEMBLY BOOM SUPPORT INSTALLATION After assembling the boom, you must define the length of it so that you can fix the boom support, as visible on the image above. When the boom’s length is decided, fix it with the two small screws situated at the end of the fix part of the boom.
- Page 7 INSTALLATION INSTALLATION TOP COVER REMOVAL SPRING ADJUSTMENT phase 5 phase 4 phase 3 phase 2 phase 1 ADJUSTMENT To adjust the springs, 1 Open the door using the key supplied 2 Rotate the rod (image above) to you must use a wrench to fasten or to unlock it and then pull it to the unlock the cover.
- Page 8 INSTALLATION INSTALLATION BOOM LEVELING LIMIT-SWITCHES AND STOPPERS ADJUSTMENT After installing the barrier, you must verify the position of the boom while closed. If it The mechanical limit-switches of the isn’t aligned horizontaly when closed, follow the instructions bellow to adjust it. barrier are shown on the image on the left.
- Page 9 MC15 CONTROL BOARD CONFIG CHECKING LIMIT-SWITCHES CONNECTIONS BARRIER’S COURSE CONFIGURATION To program the MBM6 24V you must consult the manual of the MC41SP The LEDs BL e DS must be both ON so that the barrier can work properly. control board.
- Page 10 MC15 CONTROL BOARD CONFIG MC15 CONTROL BOARD CONFIG TRANSMITTERS CONFIGURATION CONDOMINIUM FUNCTION AND POTENTIOMETERS Once you have the barrier’s course configured, you can now program the transmitters: The condominium function of this control board causes the barrier to only accept opening orders.
-
Page 11: Troubleshooting
If the motor doesn’t work, and closing with appropriate physical damaged to obstacles remove it from installation site force (page 08.B of this manual (vehicles, people, etc.). and send to our MOTORLINE for MBM6 230V). 10.A... -
Page 12: Components Test
COMPONENT TEST MAINTENANCE CONNECTIONS SCHEME MAINTENANCE To detect which are the components with problems in barrier’s installation, sometimes Check tightness of the screws that fix the it will be needed to run some tests with direct connection to a 230V power supply. For boom to the barrier’s body. -
Page 13: Control Board Connections
CONTROL BOARD CONNECTIONS CENTRAL MC15 MOTORLINE RX - Receiver CLOSE CODE CODE P. OPEN CMD AP. L CORT. PGM. AUT T. MOT T. MOT. P T. PAUSA F1=6,3TL250V F2=160mAL250V 12.A...
Need help?
Do you have a question about the mbm6 and is the answer not in the manual?
Questions and answers