Advertisement
BRIEF OF PRODUCT
* Sensor (CMOS)
Adopt SONY 1/3" CMOS Sensor.
* Auto Gain Control (AGC)
Built-in auto gain control (AGC) circuit. The color camera
can get high definition picture in low Lux condition.
* Scanning Mode
NTSC or PAL mode.
* Support UTC function
With UTC Remote Controller for the convenience of
OSD menu setting.
* OSD SETTING
3D-NR
ON/OFF
GLOBAL/CENTER/CENTERWEIGHT/BLACK
AE MODE
LIGHT/FRONT LIGHT/DISTINGUISH
IMAGE ENHANCE SHARPNESS/CONTRAST/SATURATION
IMAGE
MIRROR
ON/OFF
FLIP
ON/OFF
BRIGHTNESS
0.10.20......250
ZOOM IN
50. 60. 70. 80. 90. 100
AUTO
DAY&NI
GHT
IR-CUT
AWB-PRO
AWB-TEMPORAL
AWB-AI
WB
AWB-SZ
OSD
AWB-GW
SET
AWB-CCT
MOSAIC/WHITE/YELLOW/CYAN/GREEN/
COLOR
ZONE
MAGENTA/RED/BLUE/BLACK
MASK-
ING
AREA NO.0 - AREA
NO.7
DIREC-
AREA NO.0 - AREA
TION
NO.3
ENGLISH
LAN-
GUAGE
CHINESE
LOAD DEFAULT
SOFT VERION
SAVE&EXIT
CONNECTING
Monitor
KEY BOARD
UP
MTX1000DIR
MENU
RIGHT
LEFT
PRESS
DOWN
Link wire rule：
Video
Power
TROUBLE AND SOLUTION
1. No Picture after providing power
. May be the power supply voltage abnormity, please check the power
supply voltage and pole whether exactitude.
. Please check all the connecting cable and monitors whether be connected
correctly or not.
2. The picture level direction have flowing interference ripples
. May be caused by the power supply AC ripples, it need filter the wave of the
power supply.
. Check the monitor and peripheral equipments used.
3. The picture background color changes continuously
. The fluorescent lamp's electromagnetic field cause color roll. This is proper
phenomenon of the cameras.
. Reduce the fluorescent lamp numbers or increase the distance between the
camera and the fluorescent lamps can improve it.
. Use power supply external sync. camera can solve it.
4. The picture smear too mass
. The power supply's voltage unstable.
. Connecting cables not connect correctly or have high impedance.
INTRODUCTION
Congratulations on your purchase of this product.
This User Guide suits
the latest CMOS technical of sensor and driver. The most
Video
attractive characteristics are small and easy hidden, suits
the elevator and corridor. In addition, it owns the charac-
● Do
ters of high definition and stability, strong anti-jamming,
not
mou
rich and real color. Fixing and using this model are con-
venient too. It is very good for you to apply to yours CCTV
12V DC
system.
Please read this instruction manual carefully to en-
sure proper use of the product.
To prevent fire or shock hazarded. Do not expose the unit
to rain or moisture.
The symbol is intended to alert the user to the presence of
DC12V Power Supply
important operating and maintenance (servicing)
Instructions in the literature accompanying the appliance.
The symbol is intended to alert the user to the presence of
uninsulated 'dangerous voltage' within the product's
enclosure that may be of sufficient Magnitude to consti-
a risk of electric shock to persons.
SHOCK
DO NOT REMOVE COVER OR BANCK NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
CAUTION:
TO PREVENT ELECTRIC SHOCKS AND RISK OF
FIRE HAZARDS,DO NOT USE OTHER THAN
SPECIFIED POWER SOURCE.
Note:
● Please note the camera's operating temperature and its using
environment requirement. Avoid using the camera at too high
or too low temperatures. The operating temperature is
+60℃. (Recommendatory operating temperature is
+50℃.)
● Never make the camera face the sun or bright object. Other-
wise, it will damage the CMOS.
MTX1000DIR
product. We adopt
CAUTION:
RISK OF ELECTRIC. DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
-30~
–10~
Advertisement
