1. Manuals
  2. Brands
  3. Multi-Mover Manuals
  4. Industrial Electrical
  5. XL35
  6. User manual and parts list

Multi-Mover XL35 User Manual And Parts List

Hide thumbs
Table of Contents

Advertisement

Quick Links

Transport
* Only use stable loading surfaces with sufficient loading capacity (see section 2.2).
* Secure the MULTI-MOVER XL35 against tilting or sliding.
* It is prohibited to;
-
get under the MULTI-MOVER XL35 while lifting
-
remain within the tilting range of the MULTI-MOVER XL35 during unloading
jjo 171
MULTI-MOVER XL35
USER MANUAL and PARTS LIST
MULTI MOVER XL35
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the XL35 and is the answer not in the manual?

Questions and answers

Related Manuals for Multi-Mover XL35

Summary of Contents for Multi-Mover XL35

  • Page 1 * Only use stable loading surfaces with sufficient loading capacity (see section 2.2). * Secure the MULTI-MOVER XL35 against tilting or sliding. * It is prohibited to; get under the MULTI-MOVER XL35 while lifting remain within the tilting range of the MULTI-MOVER XL35 during unloading jjo 171 MULTI-MOVER XL35...

  • Page 2: Table Of Contents

    PARTS Chapter 10 DECLARATION OF CONFORMITY Appendix I Electrical circuit diagram Appendix II User manual battery charger Appendix III Part List Multi-Mover Europe B.V. www.multi-mover.eu info@multi-mover.eu T +31 24 744 00 70 F +31 24 890 17 90 MULTI-MOVER XL35...

  • Page 3: Introduction / Warranty / Definitions / Safety Symbols

    The user manual should be made available to the user of the Multi-Mover XL35 and must be present at the Multi-Mover XL35 when it is being used. The user manual must have been read by anyone working with/at the Multi-Mover XL35, and the instructions must be observed.

  • Page 4: Chapter 2 Technical Description

    Safety symbols On various places on the Multi-Mover XL35 you will find standardized safety symbol stickers as displayed to the right. The upper part warns against a general or particular hazard. The lower part indicates what type of hazard is being warned against and will explain what you must do.

  • Page 5: Packaging, Loading / Unloading, Towing, Recycling

    Avoid injury and damage as a result of incorrect placement of the lift truck's lift forks. Loading and unloading If the Multi-Mover XL35 has to be moved by means of a lift truck, the lift forks must be placed at the heaviest part at the rear of the Multi-Mover XL35, between the 2 large wheels.

  • Page 6: Chapter 3 Safety Regulations

    Never drive onto a slope at an angle or crosswise. Only ever drive on and off a slope at a right angle. The Multi-Mover XL35 with trailer(s) may also tip over if the bends are taken at a speed that is too high.
  • Page 7 3.10 Caution! Hazard of serious injury due to overloading the Multi-Mover XL35. The load behind the Multi-Mover XL35 may not be more than indicated at section 2.2 technical data. Make sure the trailer(s) has/have been loaded evenly and safely.
  • Page 8 Multi-Mover XL35, temporary personnel for instance. The MULTI-MOVER XL35 may only be operated after the operator has thoroughly studied the user manual and after the owner of the Multi-Mover XL35 has provided a full training / instruction concerning the operation and the safety regulations.

  • Page 9: Chapter 4 Preparation

    - other liquids and hazardous substances than stated above Optional we offer a ATEX modified XL35 The Multi-Mover XL35 does not have permission to be driven on public roads without the options required. Only use the Multi-Mover XL35 for the purpose for which it was designed.

  • Page 10: Responsibility Operator

    Only ever drive on and off a slope at a right angle. The Multi-Mover XL35 may also tip over if the bends are taken at a speed that is too high. # Maximum slope angle, with / without load 4% / 20 % Passengers may not be taken along with the Multi-Mover XL35 and towed vehicle.

  • Page 11: Regulations For Use

    Avoid bends if necessary and be careful on small hills, thresholds, etc. Reduce speed in case of sharp bends. The Multi-Mover XL35 may only be driven at speeds that allow you to stop in time, e.g. if an obstacle is standing in or entering the driving area.

  • Page 12: Operation

    Electric Magnetic brake (7) The wheels (16) are coupled to/disconnected from the motor (15) by means of the handbrake button. If the button is pulled out it is in the free position, the Multi-Mover XL35 can now be freely manoeuvred by hand.
  • Page 13 Step less speed control, Potentio Meter # Hydraulic or electric hitch Steering handles (1) The steering handle (1) with bar is a fixed part of the Multi-Mover XL35, moving to the left means driving to the left, and vice versa. Safety switch (3) Belly Butto4 When pressing the safety switch (risk of getting jammed), the Multi-Mover XL35 will stop immediate- In order to start again, the drive switch must first be placed in the neutral position.

  • Page 14: Batteries

    Battery charger connection The connection plug for the battery charger is located on the right side, in a recess of the encasing. On the dashboard of the Multi-Mover XL50, the battery indicator (8) is placed. 3 LEDs (30%) means charge asap.
  • Page 15 We therefore recommend recharging the stored Multi-Mover XL35 every 2 months. It is also possible, that there are still standby consumers in a switched off Multi-Mover XL35 (key ignition etc.), which will mean that the batteries will discharge more quickly.

  • Page 16: Coupling Trailer(S)

    5.5 Coupling trailer(s) # The Multi-Mover XL35 is made with a standard tow eye with tow pin or a ball coupling point in the middle of the Multi-Mover XL35, to which the pole of a trailer can be coupled.

  • Page 17: Cleaning

    Taking out of operation If the Multi-Mover XL35 is not used for a certain period, you will have to; connect the battery charger place the Multi-Mover XL35 on blocks, so that the tyres do not touch the ground Have maintenance and repairs performed by persons authorized by Multi-Mover Europe BV.
  • Page 18 Separate all materials that full under the category of chemical waste, such as oil, lubricants, switching material, batteries and certain electric components. Dispose them as chemical waste. Offer residual materials to recognized waste processing companies who have the required permits. MULTI-MOVER XL35...

  • Page 19: Chapter 8 Failures

    FAILURES When removing a failure, ALWAYS switch off the Multi-Mover XL35 and remove the ignition key. If a defect is established at the Multi-Mover XL35, do not use it until the repair has been complet- Failure Solution The Multi-Mover XL35 does not drive.

  • Page 20: Chapter 10 Declaration Of Conformity

    We, Multi-Mover Europe BV, Boomsestraat 38, 6613 AH Balgoij, Netherlands declare at our own full responsibility, that the Multi-Mover ***, with serial number 2018 *** to which this declaration applies, is in conformity with the provisions of the following directive(s):...

Table of Contents