Related Manuals for Derby cycle Pedelec Groove 2.0
Summary of Contents for Derby cycle Pedelec Groove 2.0
- Page 1 Original User Manual | Version 1 | 01.07.2014 Pedelec Groove 2.0 English Item no. 1973K0015013...
-
Page 2: Table Of Contents
Inhalt Introduction Storage Shipping 1 Safety Disposal General Statutory requirements 7 Charger 1.2.1 Requirements for the rider Battery 8 Display and control unit Charger Switching on and of Motor 8.1.1 Switching on Adjustments/maintenance/repair 8.1.2 Switching of Transportation of the Pedelec Assist mode 1.7.1 The Pedelec and your car Pushing assistance... -
Page 3: Introduction
The purpose of this User Manual is to help you get the Derby Cycle GmbH / Raleigh Univega GmbH most out of your Pedelec Groove 2.0 and use it correctly. Siemensstrasse 1–3 49661 Cloppenburg, Germany... -
Page 4: Safety
1 Safety breakage or failure of safety-relevant components Chapter 12 „Technical data“. Read all the safety information. Failure to observe the instructions can cause electric shock, ire and/or serious injury. The User Manual contains the following symbols that denote dangers or important information. If you wish to make any adjustments to the ride characteristics of your Pedelec, please consult your specialist cycle shop. -
Page 5: Battery
the EU in individual cases. Before using your Pe- Ideally, take the battery out of your Pedelec when delec abroad, ind out about the applicable legis- not in use. There is a risk of injury through acci- lation in the relevant country. dentally operating the battery switch. -
Page 6: Charger
Charger no longer be used, and you must have it inspected by the dealer. A battery that displays a fault must not be charged any more. The battery must not be let unattended while Children must be supervised. This will ensure that charging. -
Page 7: Motor
Adjustments/maintenance/repair Condensation may form on the charger if the temperature changes suddenly rom cold to hot. In case of condensation, wait approximately one hour before connecting the charger to the mains, until it has warmed up to the temperature of the Take the battery out before beginning work (e.g. -
Page 8: The Pedelec On Aeroplanes
for your bike in advance. As a rule, you may not take bikes 1.8.2 Motor with you on German Intercity Express (ICE) trains. Dirt should be removed rom the motor of your Pedelec regularly, ideally using a dry brush or a damp (not wet) cloth. -
Page 9: Charger
1.8.5 Charger 1.9.2 Trailers You may use a trailer with your Pedelec Groove 2.0. Always unplug the charger rom the wall socket before cleaning to avoid a short-circuit and physi- cal injury. Only use trailers that meet the requirements of the... -
Page 10: Warranty Regulations
2 Warranty regulations 2.2.3 Wear parts The following are considered wear parts under the statu- tory warranty: Warranty periods • Battery The statutory warranty valid at the time of delivery ap- • Tyres plies to all models. • Brake linings •... -
Page 12: First Steps
4 First steps Checking the tightening torques Check that all screws and important components are fas- OPEN Opening the quick-release lever tened securely and correctly. You will ind a table with im- portant screw connections and the prescribed tightening Chapter 12 „Technical data“ of the “Original torques in User Manual | General”... -
Page 13: Quick Start
5 Quick start 4. Press the battery button. The battery is ully charged when all the green LEDs on the battery are lit. Pull the plug of the charger out of the charging socket, close the cover and unplug the charger at the wall socket. Charge the battery completely before riding for the irst time. -
Page 14: Battery
8. Press the battery switch. The red LED inside it lights The carrier is only approved for a maximum of 15 6 Battery Your battery is a lithium-ion battery, the ideal type for this application. One of the main beneits is its low weight Battery switch combined with a high capacity. -
Page 15: Charging The Battery
1. Take the charger provided out of its packaging and plug it in at the wall socket (230–240 V). The LED in the charger now lights up green continuously. To charge the battery safely, the charger must be Unlocking the battery placed on a suitable surface, which should be dry and non-lammable. -
Page 16: Installing The Battery
6.1.3 Installing the battery BATTERY CHARGE DISPLAY 1. Put the battery back in the battery holder. STATE •••• 4 LEDs light up 100 – 75% The battery must be switched off before it is pushed into the battery ••• 3 LEDs light up 75 –... -
Page 17: Storage
• The number of charges Ater 1,100 charging cycles, your battery will still Make sure that the battery is ully charged before have 60% of its initial capacity, providing it has you ride your bike for the irst time or if you have been well looked ater. -
Page 19: Switching On And Of
Assist mode SYMBOL FUNCTION BUTTON PUSH a) Switch the a) 2 seconds MODE ASSISTANCE RECOMMENDATION ront and rear b) 1 second Assistance up to at Use for small climbs light on/of c) 1 second most 25 km/h (bridges etc.). b) Change the Assistance up to at indication (VEL, most 20 km/h... -
Page 20: Vel (Speed), Odo (Total Kilometres)
VEL (speed), Battery charge indicator ODO (total kilometres) The battery charge indicator shows how much charge is and DST (trip distance) available in the form of a stylised battery. The lower the charge state of the battery, the fewer black segments can When you switch the Groove 2.0 on, the display automati- be seen. -
Page 21: Range
Range Riding your Pedelec eiciently The distance you can travel using the power assist with You can monitor and inluence the cost of your journeys the battery ully charged depends on several factors: with the Pedelec yourself. You can reduce your consump- tion and therefore costs by following the tips for increas- •... -
Page 22: Troubleshooting
10 Troubleshooting 10.1 Code indication on the display If a code appears on your display, irst switch the Groove The error code is displayed until the error is cor- 2.0 system of at the battery. Wait for a moment, then rected. -
Page 23: Removing And Itting The Ront Wheel
11 Removing and itting the ront Fitting: wheel 1. Slide the cable ties with the cable on to the fork leg. Chapter 18.2.1 "Original User 2. Fit the ront wheel. Removal: Manual | General" (CD). 1. Pull apart the upper and lower halves of the electrical 3. - Page 24 Groove 2.0 drive. Reproduction, in whole or in part, is not permitted without the consent of Derby Cycle Werke GmbH / Raleigh Univega GmbH. Subject to misprints, errors and technical modiications. Derby Cycle Werke GmbH / Raleigh Univega GmbH Siemensstrasse 1–3...
Need help?
Do you have a question about the Pedelec Groove 2.0 and is the answer not in the manual?
Questions and answers