Download Print this page

Yamaha MG10/2 Service Manual page 13

Hide thumbs Also See for MG10/2:

Advertisement

2.
AC Support (Time required: About 2 minutes)
2-1
Remove the bottom case. (See procedure 1.)
2-2
Remove the screw marked [270]. The AC support
can then be removed. (Fig. 1, Photo. 1)
3.
MAIN Circuit Board
(Time required: About 8 minutes)
3-1
Remove the bottom case. (See procedure 1.)
3-2
Remove the AC support. (See procedure 2.)
3-3
Remove the ten (10) screws marked [280], the
twenty-one (21) hexagonal nuts and the eight (8)
level knobs marked [A]. The MAIN circuit board can
then be removed. (Fig. 1)
The knobs, buttons and meter cover on the MAIN
circuit board are not components of the circuit
board. When replacing the MAIN circuit board,
be sure to remove these parts according to the
following procedure.
3-4
Remove the thirty-six (36) volume knobs marked [B],
the four (4) push HPF buttons and the push PFL
button from the MAIN circuit board. (Fig. 1)
3-5
Remove the meter cover from the MAIN circuit board.
(Fig. 1)
4.
Power Switch and AC Connector
(Time required: About 2 minutes each)
4-1
Remove the bottom case. (See procedure 1.)
4-2
Remove the AC support. (See procedure 2.)
4-3
Remove the power switch by bending its claw from
the AC support. (Photo. 2)
4-4
Remove the hexagonal nut and the flat washer. The
AC connector can then be removed from the AC
support. (Photo. 2)
Downloaded from
www.Manualslib.com
AC support ( サポートAC)
Photo.1 (写真1)
manuals search engine
2.
サポート AC(所要時間:約 2 分)
2-1
ボトムケースを外します。 (1 項参照)
2-2
[270]のネジ 1 本を外し、サポート AC を外します。
(図 1、写真 1)
3.
MAIN シート(所要時間:約 8 分)
3-1
ボトムケースを外します。 (1 項参照)
3-2
サポート AC を外します。 (2 項参照)
3-3
[280]のネジ 10 本と特殊六角ナット 21 個、 [A]のノ
ブ (LEVEL) 8個を外し、 MAINシートを外します。
(図 1)
  ※MAINシート上のノブ、 ボタン、 ウィンドウMETER
は、シートの構成部品ではありません。MAIN シー
トを交換する際は、 以下の手順でこれらの部品を取
り外してください。
3-4
MAIN シートから[B]のノブ(VR)36 個とボタン
(HPF) 4 個、ボタン(PFL)1 個を外します。 (図 1)
3-5
MAIN シートからウィンドウ METER を外します。
(図 1)
4.
電源スイッチとACコネクター (所要時間 : 各約2分)
4-1
ボトムケースを外します。 (1 項参照)
4-2
サポート AC を外します。 (2 項参照)
4-3
電源スイッチのツメを曲げて、サポート AC から電
源スイッチを外します。 (写真 2)
4-4
特殊六角ナット1個と平ワッシャー1個を外して、 サ
ポート AC から AC コネクターを外します。 (写真 2)
Hexagonal nut
and flat washer
(特殊六角ナット
 と平ワッシャー)
AC connector
(ACコネクター)
AC support
Claw (ツメ)
(サポートAC)
Photo.2 (写真2)
MG10/2
Power switch
(電源スイッチ)
Claw (ツメ)
13

Advertisement

loading