Advertisement
7) Use the "ST/STP" button to set the seconds.
8) Press the "MODE" button.
"REPEAT" will be displayed at the
top of the screen and "ON" or
"OFF" will be flashing at the bottom.
9) Use the "ST/STP" button to select REPEAT "ON" or
"OFF"
10) Press the "MODE" button.
"REMIND" will be displayed at the
top of the screen and "ON" or
"OFF" will be flashing at the bottom.
11) Use the "ST/STP" button to select REMIND "ON" or
"OFF"
12) Press the "SET/RST" button to save programmed
information.
Note: When setting the Countdown Timer(s), if
programming is interrupted and no button is pushed within
2 minutes, the flashing will stop and the settings that are
shown on the screen will be held. Finish programming by
repeating Step 2 and continue as needed.
Countdown Time remains on the display. Press the
"MODE" button to rotate to Calendar Mode.
Starting/Stopping the Countdown Timer:
1) While in the selected Countdown Mode Screen, press
the "ST/STP" button to start the countdown. The
countdown timer icon located in the box at the right
side of the screen will be flashing.
2) Press the "ST/STP" button to stop the countdown. The
time remaining will be displayed.
Note: When Countdown time is set to REPEAT and
the alert is currently activated, press the "ST/STP"
button twice to stop the countdown.
3) Press the "ST/STP" button to resume counting down.
Quick Reset of Original Countdown Time:
1) Hold down the "SET/RST" button until the previously
programmed countdown time is displayed on the
screen.
2) Press the "ST/STP" button to restart at previously set
time.
OPTION MODE:
VIBRATION and SOUND alerts can be turned "ON‟ or
"OFF". The alerts that are turned ON will be activated
by the preset Daily Alarms, Countdown Timers, Hourly
alert and Button push.
HOURLY Alerts, when set "ON," will give a brief
reminder every hour on the hour with the alerts that
are turned on. (vibration, sound or both) Note: Hourly
alerts will be based on the Time Zone set to be
displayed in the Calendar Mode.
Button Alerts, when set "ON", will indentify the current
alert setting (vibration, sound or both) each time the
"MODE" or "ST/STP" button is pressed.
Option Mode Screen Abbreviation: VIBRA = Vibration
Option Mode Programming Instructions:
1) Press the "MODE" button until
"OPTION" is displayed at the top of
the screen. After approximately two
seconds "VIBRA" will be
Vibration ON
displayed. The word "ON" or "OFF" will be displayed
at the bottom of the screen.
2) Hold down the "SET/RST" button until "ON" or "OFF"
begins to flash.
3) Use the "ST/STP" button to turn vibration "ON" or
"OFF".
4) Press the "MODE" button.
"SOUND" will be displayed at the
top of the screen. "ON" or "OFF"
displayed at the bottom of the
screen will be flashing.
5) Use the "ST/STP" button to turn sound "ON" or "OFF".
6) Press the "MODE" button.
"HOURLY" will be displayed at the
top of the screen. "ON" or "OFF"
displayed at the bottom of the
screen will be flashing.
7) Use the "ST/STP" button to turn hourly alert "ON" or
"OFF"
8) Press the "MODE" button. "BUTTON" will be
displayed at the top of the screen. "ON" or "OFF"
displayed at the bottom of the screen will be flashing.
9) Use the "ST/STP" button to turn BUTTON signal "ON"
or "OFF".
10) Press the "SET/RST" button to save programmed
information.
Note: When setting the features in Option Mode, if
programming is interrupted and no button is pushed within
2 minutes, the flashing will stop and the settings that are
shown on the screen will be held.
If no button is pushed within 2 additional minutes, screen
will return to Calendar Mode automatically.
Quick Viewing of Current Option Mode Settings:
1) Press the "MODE" button until "OPTION" is displayed
at the top of the screen. After approximately two
seconds "VIBRA" will be displayed. If vibration is
currently turned on, "ON" will be displayed at the
bottom of the screen. If turned off, "OFF" will be
displayed.
2) Press the "ST/STP" button repeatedly to view other
current option mode settings. („SOUND", "HOURLY",
"BUTTON")
EL LIGHT: (DISPLAY BACK LIGHT)
Press the "LIGHT" button to turn on the backlight. Light
will stay on for approximately 3 seconds and then turn off
automatically if another button is not pushed. Light will
continue to stay on while any other button is pushed
within 3 seconds.
BATTERY:
Standard 3 volt lithium CR2032 is required. Battery must
be replaced by a qualified person to maintain water
resistance. Battery life will vary due to how often the
vibration function and EL Light are used.
IMPORTANT PRECAUTIONS:
VibraLITE watches are not intended to be worn during
swimming, diving or in the shower. Do not attempt to
open the watch to replace the battery yourself, or for any
reason, as this operation must be performed by a
qualified technician under controlled conditions.
We recommend that you retain your original sales slip as
your proof of purchase date.
ONE YEAR LIMITED WARRANTY:
Your VibraLITE 12 is warranted to be free from defects in
material or workmanship for One Year from the date of
purchase. This is a limited warranty and covers watch
functions only. This warranty does not apply to the
battery, band, case or crystals since such items are
subject to wear and tear of daily use. The warranty is void
if the watch has been tampered with, altered, abused, or
subjected to extreme conditions for which it was not
designed, or repaired other than by a qualified service
center. At its option, GLOBAL ASSISTIVE DEVICES,
INC. may select to replace the unit, rather than repair it.
During the warranty period, return the watch, with dated
proof or purchase, in a secure package, insured and with
shipping charges prepaid. No C.O.D. packages will be
accepted. Please include a note describing the service
required, your return address and include $9.95 (check,
money order, Visa, Master Card, American Express or
Discover) for shipping and handling in the USA. Other
countries please contact us for pricing.
OUT OF WARRANTY SERVICE:
Follow the same procedure for shipping to us as you
would for warranty service. Be sure to include a
description of the problem. Before any work is
performed, an estimate will be submitted for your
approval for any parts and labor not covered by the
warranty.
DISCLAIMER:
In no event shall Global Assistive Devices, Inc. be held
liable for any special, incidental, indirect or
consequential damage whatsoever including, but not
limited to, damages for loss of property, personal
injury, loss of privacy, failure to meet any duty,
negligence and any other loss whatsoever, however
caused, even if Global has been advised of the
possibility of such damages. This disclaimer of liability
applies to any damages or injury, including but not
limited to those caused by any failure of performance
of the product. Responsibility for selection, safety and
suitability of any product rests with the consumer.
Circumstances or consequences arising out of or in
anyway related to the use of or inability to use our
products is the responsibility of the consumer. Global
Assistive Devices, Inc. cannot be held liable in any
way.
GLOBAL ASSISTIVE DEVICES, INC.
Oakland Park FL 33334 USA
www.GlobalAssistive.com
www.VibraLITE.com
Advertisement
