DMP Electronics 1158 Installation Manual

Wireless eight-zone takeover module

Advertisement

Quick Links

1158 WIRELESS EIGHT-ZONE
TAKEOVER MODULE
Installation Guide
Figure 1: 1158 Housing
DESCRIPTION
When a DMP panel is installed in a
location with an existing non-DMP
panel, the 1158 Wireless Eight-Zone
Takeover Module can be used to
convert up to eight existing normally
closed, hardwired zones into wireless
zones. This allows the new DMP
panel to communicate with existing
zones.
The 1158 uses two serial numbers to
accommodate up to eight zones and
can be powered by transferring AC
and battery power from the existing
panel.
All DMP 1100 Series Wireless
Receivers and burglary
panels. See the last page for
compatibility details.

What is Included?

• 1158 Wireless Eight-Zone
Takeover Module
• Hardware pack
1

PROGRAM THE PANEL

The 1158 can be programmed with up to eight zones. When
programming the 1158 in the panel, refer to the panel
programming guide as needed.
Program the serial number associated with contacts 1
through 4 first. Then, be sure to start by programming
contact 1.
When you enter the serial number associated with contacts
5 through 8, contact 1 displays again indicating that you are
programming the first contact associated with that serial
number.
1.
In ZONE INFORMATION, enter the ZONE number, and
then press CMD.
2. Enter the ZONE NAME and press CMD.
3. Once ZONE TYPE appears, select the appropriate
zone type, and then press CMD.
4. At the NEXT ZONE prompt, select NO. If you see the
WIRELESS ZONE prompt, select YES.
Note: If you are programming the 1158 onto a
zone that can be either hard wired or wireless,
then this prompt appears. If the zone you are
programming is wireless-only, then the prompt
does not appear.
5. Enter the eight-digit SERIAL NUMBER and press CMD.
6. Enter the CONTACT number being used.
Enter the SUPERVSN TIME and press CMD.
7.
8. At the NEXT ZONE prompt, select YES and continue
to program up to seven more zones.
Note: Zones must be entered sequentially. For
example, if you begin by programming zone 71,
you would need to program zone 72 as the next
contact.
Supervisory Message
When a wireless receiver is installed, a receiver is restarted,
the panel is reset, or if programming is complete, then the
supervision time is reset.
If the receiver has been powered down for more than one
hour, then the 1158 may take up to an additional hour to send
a supervision message.
A missing message may display on the keypad until the
supervision message is sent.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 1158 and is the answer not in the manual?

Questions and answers

Summary of Contents for DMP Electronics 1158

  • Page 1 If the receiver has been powered down for more than one What is Included? hour, then the 1158 may take up to an additional hour to send a supervision message. • 1158 Wireless Eight-Zone A missing message may display on the keypad until the Takeover Module •...
  • Page 2 With the 1158's housing cover removed, use the supplied screws to secure the 1158 to a wall or other flat surface. The 1158 PCB has built-in holes to allow you to screw the housing onto a surface without removing the PCB. See Figure 2.
  • Page 3 Code de sécurité 6 de Santé Canada. Le système doit être installé à une distance minimale de 7.87 pouces (20 cm) séparant l’antenne d’une personne présente en conformité avec les limites permises d’exposition du grand public. DIGITAL MONITORING PRODUCTS 1158 INSTALLATION GUIDE...
  • Page 4 1158 WIRELESS EIGHT-ZONE Compatibility • XT30 panels with 1100D Series Wireless Receiver TAKEOVER MODULE • XT50 panels with integrated wireless receiver or 1100D Series Wireless Receiver • XR150/XR550 Series panels with 1100X Series Wireless Receivers Specifications • XTLplus panels with integrated wireless receiver •...

Table of Contents