Table of Contents
Advertisement
Quick Links
Instructions
040-1480-04
Enhanced Monitor Upgrade Kit
VX1410 IntelliFrame
070-9471-03
Warning
The servicing instructions are for use by qualified
personnel only. To avoid personal injury, do not
perform any servicing unless you are qualified to
do so. Refer to all Safety Summaries prior to
performing service.
Advertisement
Table of Contents
Related Manuals for Tektronix IntelliFrame VX1410
Summary of Contents for Tektronix IntelliFrame VX1410
- Page 1 Instructions 040-1480-04 Enhanced Monitor Upgrade Kit VX1410 IntelliFrame 070-9471-03 Warning The servicing instructions are for use by qualified personnel only. To avoid personal injury, do not perform any servicing unless you are qualified to do so. Refer to all Safety Summaries prior to performing service.
- Page 2 Copyright Tektronix, Inc. 1995. All rights reserved. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes that in all previously published material. Specifications and price change privileges reserved. Printed in the U.S.A.
-
Page 3: Kit Description
Kit Description This kit includes parts and instructions to upgrade the Standard Monitor board with an Enhanced Monitor Board (Option 1M), to replace the Top Extrusion on a VX1410 IntelliFrame mainframe, and to add an air baffle to the mainframe. Instruments There are no instrument serial numbers associated with this kit for theVX1410 IntelliFrame mainframe. -
Page 4: Service Safety Summary
Kit Description Service Safety Summary WARNING. The servicing instructions are for use by qualified personnel only. To avoid personal injury, do not perform any servicing unless you are qualified to do so. Refer to to the General Safety Summary in the VX1410 IntelliFrame Instruction Manual before performing any service. -
Page 5: Installation Instructions
These instructions assume a certain familiarity with the instrument. If you need further details, refer to the VX1410 IntelliFrame Instruction Manual. For assistance to install this kit, please call your nearest Tektronix, Inc., Service Center or Tektronix Factory Service. CAUTION. Many components within this instrument are extremely susceptible to static-discharge damage. - Page 6 Installation Instructions 8-32 Screw 8-32 Screw Chassis Ground Connection Safety Ground Screw 8-32 Screw 8-32 Screw Figure 1: Location of Fan Assembly and Ground Screw on the Rear of Mainframe Power Supply 8-32 Screws (5) Ledge Fan Cables Fan Assembly Figure 2: Removing the Fan Assembly VX1410 IntelliFrame Enhanced Monitor Upgrade Kit...
- Page 7 Installation Instructions Remove Standard Monitor To remove the Standard Monitor board, refer to Figure 3 and follow these steps: Board 1. Grasp and pull the cable tie loop until the monitor board comes loose from the Backplane board. 2. Slide the board out of the mainframe. Monitor Board Cable Tie Loop Figure 3: Removing the Standard Monitor Board...
- Page 8 Installation Instructions Enhanced Monitor Board Cable Tie Loop Figure 4: Installing the Enhanced Monitor Board Reinstall Fan Assembly To reinstall the fan assembly, refer to Figures 1 and 2, and follow these steps: 1. Line up the channel on the lower edge of the fan assembly with the ledge on the mainframe and push the channel onto the ledge.
-
Page 9: Replacing The Top Extrusion
Installation Instructions If you are going to install the Front Panel Display, continue with the next procedures. If you are not going to install the Front Panel Display, you still need to perform the following operations: Remove the top cover Move the Temperature Sense Board Calibrate the Enhanced Monitor (calibration procedure) Reinstall the top cover and add the air baffle... - Page 10 Installation Instructions Top Cover 8-32 Screws (12) Figure 5: Removing the Top Cover and Top Extrusion Remove Upper Card Before you can install the new Top Extrusion, you need to remove the upper card Guides guides. The card guides at the top and bottom of the mainframe are very similar. The main difference is that the bottom guides (IntelliGuides) include the spring-loaded shutters.
- Page 11 Installation Instructions Gently pull the card guide forward until it pops out of place. Figure 6: Removing the Top Card Guides Remove Top Extrusion To remove the Top Extrusion, refer to Figure 7 and follow these steps: 1. Clip the cable tie holding the On/Standby Switch cable in place. 2.
- Page 12 Installation Instructions 4. Use a Torx with a magnetic T-15 driver to remove the six 6-32 screws holding the Top Extrusion to the mainframe. 5. Discard the screws. 6. Carefully remove the extrusion without scratching the paint. Remove 6-32 Screws (6) Extrusion Disconnect the On/Standby Switch Cable...
- Page 13 Installation Instructions 2. Use a Torx with a magnetic T-15 driver to install the six 6-32 screws (supplied with this kit) that hold the Top Extrusion in the mainframe. 3. Line up the pin 1 indicator on the ribbon cable (the red strip) in the front of the mainframe with the pin 1 indicator on the connector (the grey arrow) on the Monitor Display board.
- Page 14 Installation Instructions Slide the card guides toward the rear of the mainframe and allow the front of the card guide to snap into place. Figure 9: Reinstalling the Top Card Guides Move the Temperature To move the Temperature Sense board, refer to Figure 10 and follow these steps: Sense Board 1.
-
Page 15: Calibration Procedure
Installation Instructions Retainer Temperature Sense Board Figure 10: Moving the Temperature Sense Board 6. Line up the pin 1 indicator on the Temperature Sense board cable with pin 1 on the connector on the Temperature Sense board. Connect the cable to the connector. - Page 16 Installation Instructions To calibrate the Enhanced Monitor Card, follow these steps: 1. Power on the VX1410 IntelliFrame mainframe. Wait for at least five minutes for the mainframe to warm up. 2. While waiting for the mainframe to warm up, start up Microsoft Windows on the PC and double click on the Microsoft Terminal progam icon.
-
Page 17: Reinstall Top Cover And Add The Air Baffle
Installation Instructions 11. Power off the mainframe and reinstall the top cover. Reinstall Top Cover and Add the Air Baffle To reinstall the top cover and add the air baffle, refer to Figure 5, and follow these steps: 1. Place the top cover on the mainframe about an inch from being all the way forward. -
Page 18: Enhanced Monitor Card Setup And Performance Verification
Installation Instructions 6. If the mainframe was mounted in a rack, follow these steps: a. Use a Torx with a T-20 tip to reinstall the ten 8-32 screws that hold the rack slides and top cover to the mainframe. b. To add the air baffle, refer to Figure 12, and use a T-10 Torx drive to reinstall the two 8-32 screws holding the air baffle and top cover to the mainframe.
Need help?
Do you have a question about the IntelliFrame VX1410 and is the answer not in the manual?
Questions and answers