Advertisement
RM-V8E.3-864-047-11.ECKA Page.2
C
English
a
Operating a Component
1
2
3
Notes on Using the Remote
Commander
Basically, use this Commander in the same way as
the Commander supplied with your TV or VCR.
• Using this Commander will not increase the
• Some functions of your TV or VCR may not work
Remote Button Descriptions
(ill. C)
Operating a TV (a)
1 To set up the commander.
2 To switch to VCR or TV operation.
3 To change the input mode.
4 To work as the JUMP, FLASHBACK or
b
5 To change the channel.
6 volume up: +
7 To mute volume on TV. Press again to turn
8 To turn on/off, or turn off the TV. (Varies
9 To display the current channel on TV, or to
!º channel up: +
Operating a VCR (b)
1 To set up the commander.
2 To switch to VCR or TV operation.
3 To switch the signals supplied to the TV
4 To change the channel.
5 Play
6 Rewind
7 Record
8 Stop
9 To turn on and off a VCR.
!º To display the on-screen menu (Sony VCR
!¡ Fast-forward
!™ Pause
!£ channel up: +
You can use the . +/– and ¤ buttons to
operate TV even if the VCR/TV switch is set to
VCR.
CCC
Troubleshooting
Make sure that the slide switch is set to the
If you're having problems setting
component you want to operate.
up or using the Remote
Point the Commander directly at the
Commander:
component.
• When setting up the Commander, carefully go
Press the button for the function you want to
through the procedures described under
use.
"Setting the Code". If the code that's listed
See "Remote Button Descriptions" for
first for your component doesn't work, try all
complete descriptions of the buttons on the
the codes listed for your component – in the
Commander.
order in which they're listed. If all the codes
fail to work (or if your component is not listed
in this manual), try using the procedures
under "Searching for the Correct Code".
• Check that you're aiming the Commander
directly at the component, and that there are
no obstructions between the Commander and
functions of your TV or VCR. The functions of
the component.
the Commander are limited to the functions of
• Check that the slide switch is set to the
the components themselves. For example, if your
component you want to control.
TV does not have a Recall function, the RECALL
button on this Commander will not function with
• Make sure the batteries you're using are not
your TV.
worn out, and that they're inserted correctly.
• Check that the component has infrared remote
with this Commander.
capability. For example, if your component
didn't come with a remote, it probably isn't
capable of being controlled by a Remote
Commander.
Specifications
Operable distance
Approx. 7 m (23 ft.) (varies
depending on the
component of each
manufacturer)
Power requirements
Two R6 (size AA) batteries
CHANNEL RETURN button, depending on
(not supplied)
the TV's brand.
Battery life
Approx. 6 months (varies
depending on frequency of
The functions of each button vary
use)
depending on your TV.
Dimensions
Approx. 61 x 191 x 30 mm
• 0 – 9 buttons: To select the number. Also to
(w/h/d)
turn on the TV.
(2
1
/
x 7
5
/
x 1
1
/
in.)
2
8
4
• ENT button: To press after the 0 – 9 buttons
Mass
Approx. 100 g (3.5 oz.)
to change the channel. (For example, to go
(not including batteries)
to channel 5, press 5 and then ENT.)
Supplied Accessories Label (1)
• 1- and 2- buttons: To select a number
Design and specifications are subject to change
between 10 and 19, and 20 and 29.
without notice.
• -/-- button: To select double digit numbers.
Component
No.
volume down: –
TV
VCR
muting off.
It will be useful to write down the code
depending on your TV. If your TV does not
numbers of your components in the chart
turn on by pressing this button, try pressing
above, so that you can refer to them when
the 0 – 9 buttons.)
registering the code numbers with the
Commander.
turn on the TV. (The function of this button
varies depending on your TV.)
channel down: –
(from the antenna or from the VCR).
The functions of each button vary
depending on your VCR.
• 0 – 9 buttons: To select the number.
• ENT button: To press after the 0 – 9 buttons
to change the channel. (For example, to go
to channel 5, press 5 and then ENT.)
• 1- and 2- buttons: To select a number
between 10 and 19, and 20 and 29.
• -/-- button: To select double digit numbers.
To record, press ( while pressing r. First
release (, then release r.
only).
channel down: –
KKK
RM-V8E.3-864-047-11.ECKA Page.2
AAA
RM-V8E.3-864-047-11.ECKA Page.2
Advertisement
