Related Manuals for Eurotech DynaPCN 10 Series
Summary of Contents for Eurotech DynaPCN 10 Series
- Page 1 WIDE-GATE CONFIGURATION DynaPCN 10-xx Passenger & People Counter Rev 1-0 – 28 February 2018 – DYPCN-10-xx_WideGate_EN_1-0 – ENGLISH...
-
Page 2: Trademarks
All trademarks, registered trademarks, logos, trade names and products names contained in this document are the property of their respective owners. Revision history Description Date Revision First release 28 February 2018 © 2018 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy... -
Page 3: Table Of Contents
DynaPCN 10-xx Rev. 1-0 Contents Contents Trademarks ................................ 2 Revision history ..............................2 Contents ..................................3 How to assemble the Wide-gate configuration ....................5 What is a Wide-gate configuration? ......................5 How to install 2 or more devices in Wide-gate configuration ..............6 Note about devices connected in Wide-gate configuration .............. - Page 4 (This page has been intentionally left blank)
-
Page 5: How To Assemble The Wide-Gate Configuration
DynaPCN 10-xx Rev. 1-0 How to assemble the Wide-gate configuration How to assemble the Wide-gate configuration What is a Wide-gate configuration? Typically, a single DynaPCN installed 200 cm above the floor, allows you to detect gates having widths of about 160 cm. If the gate is wider you may need to connect together two or more DynaPCN devices. -
Page 6: How To Install 2 Or More Devices In Wide-Gate Configuration
How to assemble the Wide-gate configuration DynaPCN 10-xx Rev. 1-0 How to install 2 or more devices in Wide-gate configuration When installing two or more devices in Wide-gate configuration: • Keep the devices aligned with respect to the gate • Keep a distance of 80 cm between the centres of the devices •... -
Page 7: Note About Devices Connected In Wide-Gate Configuration
DynaPCN 10-xx Rev. 1-0 How to assemble the Wide-gate configuration Note about devices connected in Wide-gate configuration The figure below shows 3 types of Wide-gate configuration, all managed by the same Control Unit (for example the Host PC). The Control Unit detects each Wide-gate configuration as an entity: •... -
Page 8: How To Set Up The Wide-Gate Parameters
How to set up the Wide-Gate parameters DynaPCN 10-xx Rev. 1-0 How to set up the Wide-Gate parameters To set up the DynaPCN parameters for the Wide-Gate configuration, complete the following steps: 1. Restore the factory settings. Use WinClient to restore the factory settings in each DynaPCN device (Master and Slaves) that you are connecting in Wide-Gate configuration. - Page 9 DynaPCN 10-xx Rev. 1-0 How to set up the Wide-Gate parameters 6. Cycle the power on all the DynaPCN devices. Cycle the power on all the devices and wait for the devices to boot. When the boot is completed all the devices are ready for “Wide-Gate” counting operations 7.
- Page 10 (This page has been intentionally left blank)
-
Page 11: Notes
DynaPCN 10-xx Rev. 1-0 Notes Notes 11 / 12... - Page 12 HEADQUARTERS For your Eurotech local contact refer to: eurotech.com/contacts Via Fratelli Solari, 3/a For the Eurotech Global Support Centre refer to: support.eurotech.com 33020 Amaro (UD) – Italy Tel: +39 0433.485.411 Fax: +39 0433.485.499 For the Eurotech Download Area refer to: eurotech.com/download...
Need help?
Do you have a question about the DynaPCN 10 Series and is the answer not in the manual?
Questions and answers