Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for MK Diamond Products MK-2000P
Summary of Contents for MK Diamond Products MK-2000P
- Page 1 MK-2000P Hand held Wet Core Drill www.mkdiamond.com OWNER’S MANUAL & OPERATING INSTRUCTIONS Revision 101 08.2018 Manual Part# 158490 Caution: Read all safety and operating instructions before using this equipment. This parts list MUST accompany the equipment at all times.
- Page 2 INTRODUCTION Congratulations on your purchase of a MK-2000P Handheld Drill. We are certain that you will be pleased with your purchase. MK Diamond takes pride in producing the finest construction power tools and diamond blades in the industry. Operated correctly, your MK-2000P Handheld Drill should provide you with years of service. In order to help you, we have included this manual.
-
Page 3: Table Of Contents
TABLE OF CONTENTS SAFETY Safety Messages General Safety California Proposition 65 Message Safety Label Pre-Start Safety 9-10 Product Specification OPERATION Main Instruction Auxiliary Handle Gear Shifting MAINTENANCE & TROUBLESHOOTING Water Supply & Electrical Safety Care & Maintenance ORDERING and RETURN INSTRUCTIONS Ordering Information Return Material Policy Packaging Instructions... -
Page 4: Safety Messages
MK-2000P SAFETY Read and follow all safety, operating and maintenance instructions. Failure to read and follow these instructions could result in injury or death to you or others. Failure to read and follow these instructions could also result in damage and/or reduced equipment life. Safety warnings and guidelines do not by themselves eliminate danger. - Page 5 MK-2000P SAFETY PERSONAL PROTECTIVE EQUIPMENT ALWAYS wear approved respiratory, head, ear and eye protection when operating this machine. ACCIDENTAL STARTS! Before starting the engine/motor, be sure the ON/OFF switch is in the OFF position to pre- vent accidental starting. Place the ON/OFF switch in the OFF position before performing any service operation.
- Page 6 MK-2000P SAFETY USE PROPER APPAREL DO NOT wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry that may be caught in moving parts. Non-slip footwear is recommended. Wear protective hair cover- ing to contain long hair. SECURE WORK Clamps or a vise should be used to hold work whenever practical. Keeping your hands free to operate a power tool is safer.
- Page 7 MK-2000P SAFETY CHECK FOR DAMAGED PARTS Before using a power tool, check for damaged parts. A guard or any other part that is damaged should be carefully checked to determine if it would operate properly and perform its intended function. Always check moving parts for proper alignment or binding.
-
Page 8: California Proposition 65 Message
MK-2000P SAFETY SILICA DUST WARNING Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other minerals and rocks. Repeated and/or substantial inhalation of airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis. -
Page 9: Safety Label
Use metal detection systems if needed. Check the MK-2000P for damage prior to use. Inspect the cord and plug for cuts, frays and damage. Have damage repaired by authorized repair technicians. Take care that the ON/OFF switch is in the OFF position before inserting the plug into a power receptacle. -
Page 10: Product Specification
158365 OPERATING THE MK-2000P Auxiliary Handle In hand held drilling operations, only use the MK-2000P with the Auxiliary Handle fixed. The Auxiliary Handle must be tightened on the collar, by turning the lever. ON/OFF SWITCH The MK-2000P is equipped with an electronic ON/OFF switch. -
Page 11: Gear Shifting
10 mm) in depth. Once the pilot hole is created, the centering bit can be removed and replaced for full speed operation. OVERLOAD PROTECTION To protect the operator and the drill, the MK-2000P is equipped with three overload protective devices - mechanical, electronic and thermal. In case of overload, the MK-2000P is equipped with warning device. Mechanical Overload Protection If the core bit is suddenly blocked in the hole, a clutch will slip, disengaging the bit from the motor. -
Page 12: Care & Maintenance
WATER SUPPLY The MK-2000P is equipped with an intake cooling water flow control valve that can be placed vertically of horizontally. A quick disconnect is supplied with the unit for ease of operation. - Page 13 NOTES...
-
Page 14: Ordering Information
ORDERING, RETURN & PACKAGING ORDERING INFORMATION You may order MK Diamond products through your local MK Diamond distributor or, you may order direct from MK Diamond. When ordering direct from MK Diamond, please have the following information ready before calling: •... -
Page 15: Contact
© COPYRIGHT 2012, MK DIAMOND PRODUCTS, INC. ALL RIGHTS RESERVED. The MK Diamond logo is a registered trademark of MK Diamond Products, Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property of their re- spective owners and used with permission. - Page 16 MK-2000 Handheld Drill OWNER'S MANUAL & OPERATING INSTRUCTIONS MK Diamond Products, Inc. 1315 Storm Parkway Torrance, CA 90501 Toll-Free: (800) 421-5830 Phone: (310) 539-5221 Fax: (310) 539-5158 www.mkdiamond.com...