1. Manuals
  2. Brands
  3. Splash SuperPools Manuals
  4. Swimming Pool
  5. SuperPool
  6. User manual

Splash SuperPools SuperPool User Manual

Hide thumbs

Advertisement

Table of Contents

User's Guide
©
2003-Splash Superpools Ltd.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SuperPool and is the answer not in the manual?

Questions and answers

Erik
June 17, 2025

The best way to cut a hole for the return hose?

0

Subscribe to Our Youtube Channel

Related Manuals for Splash SuperPools SuperPool

Summary of Contents for Splash SuperPools SuperPool

  • Page 1 User’s Guide © 2003-Splash Superpools Ltd.
  • Page 2 If you have any questions on the assembly of your Splash SuperPool or Splash OmegaPool, please call your local Splash SuperPools dealer. Splash SuperPools, LLC • 3912 East Progress • North Little Rock, AR USA 72114 (800) 92-SPLASH • http://www.splashpools.com ©...

  • Page 3: Congratulations

    Be sure that you have an area that is smooth, level and 4 feet larger than the pool to assemble your SuperPool. Remove all sticks, rocks, and any sharp objects. Remove and cap off any sprinkler heads, fill voids, depres- sions, or hollows with dirt or sand.

  • Page 4: Table Of Contents

    Table of Contents Congratulations! ..................3 SuperPool Parts List ................5 Getting Started ..................6 Installing Circulation System ..............10 Adding Optional Skimmer ..............12 Filling and Starting Your Pool ...............13 Omega Parts List..................14 Omega Assembly Instructions ..............15 Vacuuming Your Splash SuperPool ............20 Cleaning Filter and Pump Basket ............19...

  • Page 5: Superpool Parts List

    Splash SuperPools Parts List A. Male Top Rail End Piece I. Hose w/Threaded Nipple/Gasket B. Middle Top Rail Section J. Floating Skimmer Weir C. Female Top Rail End Piece K. Skimmer Hold Down Fitting D. Leg L. Skimmer Basket E. SplashBlox M.Skimmer...

  • Page 6: Getting Started

    CAUTION: Electrical outlet will require GFI (ground fault interruption) protection. Hint: Your SuperPool skimmer can be even more effective if located at the prevailing “down wind” end of the pool. WARNING: Make sure you do not install your pool under electrical lines.
  • Page 7 3. Above is an illustration of the assembly of the Splash SuperPool Legs. Slide the two Stainless Steel Rings onto the Leg. Continue this process until you have assembled all the Buttress Legs. Item 2A Item 2B 4. Insert the Leg into the Top Rail as in Item 2A, spreading the Leg apart until it slides into the holes. When all the buttresses are inserted, the pool will look like Item 2B.
  • Page 8 7. Position the short wall Top Rails so they are leaning over and on top of the long wall Top Rails. WARNING: Shallow water! Never jump or dive into a Splash SuperPool; serious bodily injury could occur. © 2003-Splash Superpools Ltd.
  • Page 9 Note: The Buttress Leg must be placed in the center of the support. 9. In the positioning of your Splash SuperPool, make sure that all Buttress Leg tubes are still inserted properly into the Top Rail. Do this by placing your hand on the Top Rail where the individual Leg tubes insert, and feel with thumb and fingers.

  • Page 10: Installing Circulation System

    3. Pump and Filter Installation — Please refer to the directions supplied by the manufacturer of your pump and filter. NOTE: The 17' x 29.5' SuperPool has holes for an optional extra skimmer. If you choose not to use an extra skimmer, use the supplied Wall Fittings and plugs to seal holes.
  • Page 11 Due to this potential hazard, we are recommending that you affix the Warning Label. WARNING: NEVER work on pump, filter, or skimmer while pump is operating or serious injury could occur due to strong suction. © 2003-Splash Superpools Ltd.
  • Page 12 Adding the optional second skimmer to your SuperPool When installing a second Skimmer, attach the Skimmers and returns as shown in the previous instructions. Install one of the Tee Fittings into the suction side of the pump and filter (in the leaf basket). Connect the hoses from the Suction Fittings on the pool (bottom fittings) to the Threaded Nipples.

  • Page 13: Filling And Starting Your Pool

    5. Start enjoying your pool. WARNING: SHALLOW WATER! NEVER JUMP OR DIVE INTO A SPLASH SUPERPOOL! WARNING: NEVER work on pump, filter or skimmer while pump is operating or serious injury could occur due to strong suction. © 2003-Splash Superpools Ltd.
  • Page 14 D. Clear Elastic PVC Hose E. Connecting Pins F. Wall Fittings G. Hose w/Threaded Nipple/Gasket H. Floating Skimmer Weir I. Skimmer Hold Down J. Skimmer Basket K. Skimmer L. Vacuum Adapter Plate M.Ball Valve N. Eyeball Fitting © 2003-Splash Superpools Ltd.
  • Page 15 2. Spread the pool out over the cleared surface. Line up holes in the pool (where Skimmer attaches) with the electrical outlet that is planned for the pump and filter. WARNING: Shallow water! Never jump or dive into a Splash SuperPool; serious bodily injury could occur. © 2003-Splash Superpools Ltd.
  • Page 16 Continue assembly around the entire pool. Before exiting the pool, attach the Skimmer (K) as shown in figure 4B. WARNING: Strong suction! Never lay on or insert body parts into skimmer while pump is operating. © 2003-Splash Superpools Ltd.
  • Page 17 (It may be necessary to pull the Elastic Hose to take out a wrinkle.) After pool has been filled with water, remove the Elastic Hose and save for future use. WARNING: Strong suction! Never lay on or insert body parts into skimmer while pump is operating. © 2003-Splash Superpools Ltd.
  • Page 18 7. Connect the pump and filter (as shown in Figure 7) and fill pool with water. WARNING: Strong suction! Never lay on or insert body parts into skimmer while pump is operating. © 2003-Splash Superpools Ltd.

  • Page 19: Vacuuming Your Splash Superpool

    Vacuuming Your Splash SuperPool To vacuum your pool, you may either use an automatic cleaner or the traditional manual method. If you choose the manual method, you will need a 1.5" flexible vacuum hose of adequate length, a vinyl liner vacuum head, and a telescopic pole.

  • Page 20: Cleaning Filter And Pump Basket

    1. Remove pump lid and clean pump basket. Replace lid. 2. Open Ball Valve, remove Threaded Plug from Return Wall Fitting, and close Air Relief Valve. 3. Turn power to the system back on. WARNING: Pump must be shut off when cleaning © 2003-Splash Superpools Ltd.
  • Page 21 Note: If your area does not experience freezing temperatures, disregard items 2-6. Accessories Visit the Splash web site (www.splashpools.com) for a complete line of accessories available for the Splash family of pools. CAUTION: Failure to lower water level could result in ice damage to your pool. © 2003-Splash Superpools Ltd.

  • Page 22: Ladder Assembly

    SplashLadder Assembly Instructions © 2003-Splash Superpools Ltd.
  • Page 23 F. (2) Top Ladder Handles O.(2) Long Metal Screws P. (2) Metal “J” Hooks G. (2) Vertical Supports (White) Q.(1) Ladder Tool H. (2) Exterior Step Rails (White) I. (1) Metal Berth Pipe R. (1) Warning Label © 2003-Splash Superpools Ltd.
  • Page 24 Interior Step Rails. 3. Now insert two Metal Pins into the Interior Step Rail’s holes. 4. Push the Interior Step into place. Use the same procedure for the remaining Interior Step. © 2003-Splash Superpools Ltd.
  • Page 25 1. Insert the two Top Ladder Handles into the assembled Interior Step’s holes. 2. Insert the Assembled Platform, lining up the holes for the Metal Screws. 3. Insert the Metal Screws, apply the Nuts and Washers and tighten with the Ladder Tool. 4. The Interior Steps are now complete. © 2003-Splash Superpools Ltd.
  • Page 26 2. Line up the holes of the Platform piece and the Exterior Steps for the Metal Screws. 3. Using the Ladder Tool, tighten the Metal Screws with the corresponding Nuts and Washers. 4. The SplashLadder assembly is now complete. © 2003-Splash Superpools Ltd.
  • Page 27 Hooks to the Berth Pipe with the corresponding nuts. (A wrench will be required for this step). 6. Tighten the long screws on the Berth Pipe and Bottom Ladder Supports. Screw the Round Plastic Caps (S) onto the exposed thread of the “J” Hooks. Your Splash Ladder is now secure. © 2003-Splash Superpools Ltd.
  • Page 28 5. Place the Warning Label on the outside of an Exterior Step. WARNING: Shallow water! Never jump or dive into any above ground pool; serious bodily injury could occur. If you have any questions on the assembly of the SplashLadder, please call your local Splash dealer. © 2003-Splash Superpools Ltd.

  • Page 29: Omega Ladder

    Washers. 4. The OmegaLadder “Horseshoe” Berth Pipe is now secure. 5. Slide the OmegaLadder Vertical Supports into the OmegaLadder “Horseshoe” Berth Pipe until the snap couple system is in place. The OmegaLadder assembly is now complete. © 2003-Splash Superpools Ltd.

Table of Contents

Save PDF