1. Manuals
  2. Brands
  3. 2VV Manuals
  4. Temperature Controller
  5. ESSENSSE NEO COMFORT
  6. Installation and operation instructions manual

2VV ESSENSSE NEO COMFORT Installation And Operation Instructions Manual

Air curtains
Hide thumbs Also See for ESSENSSE NEO COMFORT:
Table of Contents

Advertisement

Quick Links

Download this manual
ESSENSSE NEO
COMFORT
EN Installation and operation instructions

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ESSENSSE NEO COMFORT and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for 2VV ESSENSSE NEO COMFORT

Summary of Contents for 2VV ESSENSSE NEO COMFORT

  • Page 1 ESSENSSE NEO COMFORT EN Installation and operation instructions...

  • Page 2: Package Contents

    CONTROL THE DELIVERY PACKAGE CONTENTS PLEASE NOTE Check the product for damages immediately after delivery In case damage on the packaging, contact the carrier Claims not filed in due time will be disregarded. Check that it corresponds to the type of product ordered. •...
  • Page 3 1. INSTALLATION 1.2 EXTERNAL ACCESSORIES COMFORT MASTER Regulation module Master Comfort RGJ-VCE2-CO-*- RGJ-VCE2-CO-*- RGJ-VCE2-CO-*- Control panel boitier de commande 0-10 24VAC ModBUS RTU via INPUT INPUT INPUT Rs485 Entrée Entrée Entrée Entrée Control panel Control panel Control panel Control panel boitier de commande boitier de commande boitier de commande...
  • Page 4 1. INSTALLATION COMFORT SLAvE Regulation module Slave Comfort RGJ-VCE2-CO-*- RGJ-VCE2-CO-*- RGJ-VCE2-CO-*- ntrée Control panel Control panel Control panel boitier de commande boitier de commande boitier de commande 0-10 0-10 0-10 24VAC 24VAC 24VAC ModBUS RTU via ModBUS RTU via ModBUS RTU via Rs485 Rs485 Rs485...

  • Page 5: Connecting External Accessories

    2. EXTERNAL ACCESSORIES 2.1 CONNECTING EXTERNAL ACCESSORIES PLEASE NOTE The unit must be disconnected from the power supply to connect accessories. • All external control components must be connected according to the wiring diagram. • 2.1-1 DS door contact TECHNICAL INFORMATION –...
  • Page 6 2. EXTERNAL ACCESSORIES 2.1-5 Room thermostat - TER-P TECHNICAL INFORMATION - Room thermostat to regulate heating – Cable - Two-core cable with a cross-section of 0.5 mm , 230 V/ 50 Hz. ATTENTION! Not included with the product. 3. COMMISSIONING PLEASE NOTE Before starting up the unit, check the following: Did you leave inside tools or objects that could damage the unit?
  • Page 7 4. CONTROL READ CAREFULLY! Before the initial commissioning, check: that the device is well fastened to the support structure, • that the device is properly closed • that the power supply is properly connected, including the earthing and the external trigger protection, •...

  • Page 8: Settings Menu

    4. CONTROL Current status This screen show the detailed status of the unit: • Current air-flow settings (step or %), information icons • Heater output settings (if included) Information on the type of unit Back to previous screen The settings can be found below, under “SUBUNITS” Indicates heating is blocked (summer mode) Settings MENU...
  • Page 9 4. CONTROL Timer Language Unless otherwise set, the unit goes on stand-by mode after the timer expires. There are 5 languages available Weekly mode Activate/deactivate timer Select lan- Annual mode guage Back to main Confirm screen + return Confirm Back to main screen + return Weekly mode Lightning settings...

  • Page 10: Service Menu

    4. CONTROL Service menu MENU - FILTER TIMER Use this menu to set the period (in motor hours) after which Enter code 1616 to access the service menu you will be reminded to replace the filters or reset to timer. 1616 Set the time after which a notice will appear in...
  • Page 11 4. CONTROL MENU - USER LOCK Use this menu to set the limits to control the regulator with a Ventilation rate with open doors multi-level panel (33%-100%) Heating settings with Heat open door 0% open doors Limit level – see Ad1) Manual = 0%, 50%, 100% Enter PIN 0000~9999 (numeric values only)
  • Page 12 Ad 1) – Use one door contact as main. Its status will be sent to the SLAVE regulators and it will no longer be necessary to connect it to each regulator, if required. Not allowed = the door contact will not transmit to the SLAVE regulator from the MASTER Allowed = the door contact will transmit to the SLAVE regulator from the MASTER Ad 2) –...

  • Page 13: Menu - Factory Reset

    MENU - FACTORY RESET Use this to reset the default values Press “FACTORY RESET” to reset the default values of MENU 1616 Once completed, we recommend to turn the main supply off and on. 5. MALFUNCTIONS 7.1 MALFUNCTIONS Disconnect the main power supply before any intervention to the unit. If you are not sure of the correct steps, do not attempt to perform any repairs and call a professional service! Unit Description...

  • Page 14: Maintenance

    7.1 IF YOU ARE UNABLE TO REPAIR THE UNIT If you were unable to solve a problem, contact the supplier or the representative of 2VV. Warranty and post-warranty service are provided by the supplier or an authorised service included in the list available at the supplier’s.
  • Page 15 8. WIRING DIAGRAM...
  • Page 16 8. WIRING DIAGRAM...
  • Page 17 8. WIRING DIAGRAM...
  • Page 18 8. WIRING DIAGRAM...
  • Page 19 8. WIRING DIAGRAM...
  • Page 20 8. WIRING DIAGRAM...
  • Page 21 9. CONCLUSION 9. CONCLUSION In case of any doubt or query, do not hesitate to contact our sales or technical support departments. CONTACT Address: 2VV, s.r.o., Poděbradská 289, 530 09 Pardubice, Czech Republic Internet: http://www.2vv.cz/contact.distribution.php...

Table of Contents