Download Print this page

Eastbound MotoWinch Operating Instructions

Advertisement

Quick Links

Content
About this manual
1. Brief Description
2. Technical Specifications
3. Safety
4. Components and application
5. First use as MotoWinch
6. Maintenance
About this manual
When text follows a marker (as shown on the left), this means that an important warning indicates that
there is a danger of injury to the user or damage to the device or the motorbike.
Note; the user is responsible for adequate and personal protection while using the MotoWinch at all
times.
1.
Brief Description and disclaimer;
The MotoWinch shall only be used as described in these operating instructions. The MotoWinch is not suitable for general
lifting purposes or for applications other than those described in the operating instructions. Using the MotoWinch implies the
supplier's indemnification for damage caused by incorrect or improper use.
NOTE; the MotoWinch is a great tool but it is not a substitute for common sense and
safe riding!
2.
Technical Specifications
Article nr.
1707001
Length
112cm
Gross weight
1885 gram
3.
Safety
Avoid to come into contact with moving parts during use. Serious injury may occur. Make sure that the
strap is always rolled evenly. An unevenly rolled strap can cause blocking or damage of strap and
ratchet. Always use the rubber anti-slip foot on hard surfaces. If the surface is slippery, e.g. due to oil
leakage, moss or algae growth, there is a substantial risk that the rubber foot does not provide
sufficient stability. It is up to the user to make a safe assessment of the situation. However, during the
winching, the user must always take position such that, in case of sudden sideway slippage or failure of
the winch, the motorbike cannot fall against or on the user.
4.
Components and application
Explanation of the parts;
The Ratchet;
The ratchet is a standard 3 ton or 5 ton (optional) cargo ratchet. The ratchet lever is of such size that the power required for
the various applications is limited. The ratchet must be clean when used and inspected for possible damage. The ratchet has
been pre-mounted to the MotoWinch tube with a pipe locking pin.
The strap;
The strap is a standard 2 ton 200cm strap for use with the MotoWinch. The strap must be at all times undamaged for use in
the MotoWinch. After use, the strap should be cleaned from sand, dirt and grease. If the strap is badly frayed, torn or when the
stitching is broken, it should be replaced. In case of doubt please contact Eastbound. Using a damaged strap is entirely at
users own risk.
MotoWinch
Operating instructions
1
1
1
1
1
1
2
4

Advertisement

loading

Summary of Contents for Eastbound MotoWinch

  • Page 1 The strap; The strap is a standard 2 ton 200cm strap for use with the MotoWinch. The strap must be at all times undamaged for use in the MotoWinch. After use, the strap should be cleaned from sand, dirt and grease. If the strap is badly frayed, torn or when the stitching is broken, it should be replaced.
  • Page 2 Check if all parts are present and undamaged. Assemble the MotoWinch Parts 1 through 9 as shown below. Pay attention that part 5 is orientated correctly, with spindle on top and lever at bottom. On very soft or marshy surfaces, you also use the Teflon foot plate (optional) for load spreading.
  • Page 3 By pulling up the ratchet, the strap will roll on the spindle and the bike will move. Put your foot against the rubber foot of the MotoWinch to stabilize it and as an extra precaution against slippage of the rubber foot.
  • Page 4 Nothing in this publication may be reproduced and / or made public by print, photocopy, microfilm or any other means without the prior written permission of the publisher. Technical data may be changed without prior notice. Eastbound is not responsible / liable for damage / personal injury due to (incorrect) use of this product.