Flycolor A-CW018003 User Manual

R
User Manuel for Brushless
Thank you for purchasing our brushless electronic speed controller (ESC) . Improper operation may cause
personal injury and equipment damage. This high power system for RC model can be dangerous ,we strongly
suggest users read the instruction carefully and completely. We will not assume any responsibility for personal
ATTENTION
injury ,property damage, or any consequential damages resulting from our product.
01
Main features
● Well-designed drive firmware for brushless sensor-less 3 phase motor, smooth, delicate handle of speed control .
● With high performance MCU, low internal resistance MOSFET and imported components. High reliability, with low impedance circuit board, strong resistance
current,less heat production.
● 8 acceleration options. Applied for all kinds of RC cars.
● 8 timing options, make motor work with the best efficiency.
● Multiple protection functions: battery low voltage protection, over temperature protection, throttle signal loss protection, motor blocked protection, etc.
● Easy to use, set parameters with radio and programming card ,according to sound prompt.
02
Specification
A-CW018003
Model
Cont. Current 18A
Burst Current 50A
Battery
Linear BEC; 2S Lipo or equivalent NiHM BEC output:6V/2A; 3S LIPO or equivalent NiHM BEC output:6V/1A
BEC
≥ 12T(2040 size Motor) ≥ 12T(2040 size Motor)
Motor suppor t
Heat-dissipating Aluminum Heatsink Aluminum Heatsink
Suitable Car 1:18/1:16
Motor Type Brushless sensorless Brushless sensorless
Dimension 34*29*19mm
40g
Weight
03
Wiring Diagrams
ESC
Switch
see detail
04
Operation Instruction
1
Connect all the equipments as the wiring diagram, and go to next step.
Note: We strongly advise the use of battery connections that do not allow reverse polarity , or ESC will be damaged.
Please disconnect the battery and ESC , if not use for a long time to avoid damaging battery and accidents.
2 Set throttle range ( refer the setting process of throttle range)
First time to use remote control transmitter or change the parameters ,like throttle middle point, ATL, EPA , throttle range will be set again.
Remote control transmitter ABS must be set as "OFF", set throttle channel direction as "REV", set throttle trim as "0", EPA/ATL clockwise and
anticlockwise direction of throttle channel are set as 100% ( Max.), or it may cause no work or misoperation.
L ig htning
Car ESC
●18A
●25A
●3 5A
●4 5A
A-CW025003 A-CW035003
25A 35A
90A 190A
LiPO:2-3S；NIHM:6-10cell
≥ 9T(3650 size Motor) ≥ 5.5T(3650 size Motor)
Aluminum Heatsink
Aluminum Heatsink + Fan
1:18/1:16 1:18/1:16
Brushless sensorless
34*29*19mm 34*29*19mm 34*29*31mm(Including Fan)
42g 46g
*Please ensure all solder joints are insulated with
heat shrink where necessary
Battery
Motor
Gear
Receiver
1
Turn off ESC power
s e r ie s
switch and turn on
transmitter power
switch.
1.Keep the throttle stick in
t h e n e u t r a l p o s i t i o n . P r e s s
"set" button,green LED flashes
once.Neutral point of the throttle
is now memorized.
3
After Wire connection and basic setting, and motor prompt tone finshed, the ESC can work.
A-CW045003
● After setting ,Turn off the power , and turn on again, the ESC will ready for working.
45A ● Indicator function : red light flashes when motor run.When motor run with full throttle ,green light flashes.
●
Reset to factory default setting: press the "set" button more than 3 seconds, then red and green lights will flash 3 times, all the setting will
260A
to be the factory
05
Setting options
*Shadow par ts are factory default value
1:10
Setting options
Brushless sensorless
1.Running Mode
2.Fixed Area
54g
Accelerator
3.Initial Brake Force
4.Low Voltage
Protection
5.Star t Mode
(Punch)
6.PWM
7.Max Reverse Force
8.Max Brake Force
9.Drag Brake Force
10.Timing
11.Motor Direction
Adjustment
12.Over heat
Protection
13.Lipo Cells
1.Running Mode:
● For ward with brake : only for ward, reverse throttle is brake, no Reverse, it's mainly used for racing.
"Set" ●
For ward and reverse with brake : with reverse function, when push throttle from for ward to reverse area, RC car is in the brake state and throttle.
must be back to the middle point. RC car will reverse when motor stops rotating .This mode is used for practice.
"On"
● For ward and reverse : Push throttle from middle point to reverse area, motor will rotate reverse immediately. This mode is used for rock crawler.
"Off"
2.Fixed Area Accelerator
3.Initial Brake Force:the brake force on motor when brake is in the initial position of throttle.
4.Low Voltage Protection
lower than set value, it will cut off motoroutput.
5.Star t Mode(Punch):9 level, default is 6 level, choose the appropriate acceleration according to the field and personal preference. The higher level,
the faster the star t acceleration , but high demand for battery discharging ability( it will cause abnormal star t when battery capacity isn't enough ).
6 PWM :Working frequency ,8KHz、12KHz,choose the appropriate working frequency according to the features of motor and battery.
7.Max Reverse Force :4 options : 25% 50% 75% 100% , different option with different force. Recommend to use the smaller options, to avoid crashing
for the force is too heavy when back up.
8.Max Brake Force :ESC with potential brake the max. brake force is that the brake force when push throttle stick to the brake limit point. Choose the
appropriate brake force according to personal preference and specific situation
9.Drag Brake Force :Push throttle stick from for ward area to middle point,produce brake force for motor,it's easy for slowing down.star ting the turns.
10.Timing : Options :0° ,3.75° ,7.5° ,11.25° ,15°(default) ,18.75° ,22.5° ,26.25° ,Purpose are:
●
Compatible with different types motor. If not work with default timing , please change the appropriate timing.
● Change motor Max.RPM by changing timing. Timing is higher , output RPM is faster, power consumption is bigger.
●
Make motor work in the best efficiency point by changing timing.
● Auto timing can change timing between 0°and 30°automatically .
11.Motor Direction Adjustment
12.Over heat Protection
13.Lipo Cells: Auto : count Lipo cells automatically; 2S,3S :choose the corresponding values according to battery cells number.
Press"Set" button Green LED flashes
Red LED flashed
and turn on power "N" times indicate
continuously.
supply switch battery cells No.
3.Move the throttle stick to the
2.Move the throttle stick to full
full reverse position.Press the
forward position,Then press the
"Set" button and green LED will
"Set"button, the green LED will
flashes 3 times. Full reverse
flashes twice.Now the full forward
throttle is memorized.
throttle position is memorized.
default se tting . (this operation will not work during the process of setting throttle range
Option1# Option2# Option3# Option4# Option5#
For ward with For ward and For ward and
reverse with
brake reverse
brake
6% 9% 12%
0% 5% 10% 20%
Non-
2.6V 2.8V 3.0V
protection
Level 1
Level 2 Level 3 Level 4
8KHz
12KHz
25% 50% 75% 100%
50% 60% 70% 80%
0% 5% 10% 20%
0° 3.75° 7.5° 11.25°
For ward Reverse
Non-
Protection
Protection
Auto 2S 3S
: 6% 9% 12% ,choose as personal preference .
:To protect battery damage from over discharging .ESC will monitor battery voltage during running process, once voltage is
:Change motor rotation direction with this option.
:ESC or motor temperature is very high ( over 95°), this option decides if cut off the motor output, default is protection.
2
Enters to throttle
Release "Set"button
range setting
Red LED stops
(See Pic. below)
flashing.
Enters to Programming
Continuously press
procedure.
"Set"button.
(See page 2)
4.Return throttle stick to
neutral position. All ranges
now configured.
or programming)
Option6# Option7# Option8# Option9#
30% 40% 50% 60%
3.2V 3.4V
Level 5 Level 6 Level 7 Level 8 Level 9
90% 100%
40% 60% 80% 100%
15° 18.75° 22.5° 26.25°