Industrial Scientific M40 Instruction Manual
  1. Manuals
  2. Brands
  3. Industrial Scientific Manuals
  4. Monitor
  5. M40
  6. Instruction manual

Industrial Scientific M40 Instruction Manual

Multi-gas monitor
Hide thumbs
Table of Contents

Advertisement

Quick Links

P
N /
1
1 7
- 0
8 8
9 7
R
v e
4
P
i r
t n
d e
0
0 7
- 4
0 5
0 0
S
e p
i c
c i f
t a
o i
s n
S
u
b
e j
t c
o t
C
h
a
n
e g
G
U
A
R
A
N
T
E
E
D
.
0 1
1 0
O
a
k
d
a
e l
R
a o
, d
O
a
k
d
a
, e l
P
A
5 1
(
1 4
) 2
8 7
- 8
3 4
3 5
•
T
o
l l
F
r
e e
- 1
0 8
- 0
D
E
F
A
X
1 4
- 2
8 7
- 8
3 8
3 5
•
S
r e
i v
e c
D
p e
. t
- 1
7 0
- 1
5 1
0 0
T
E
C
T
S
8 8
- 8
8 7
- 8
3 4
3 5
M
U
L
T
- I
G
A
S
M
O
N
I
T
O
R
I
s n
u r t
i t c
n o
M
a
u n
l a

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the M40 and is the answer not in the manual?

Questions and answers

Related Manuals for Industrial Scientific M40

Summary of Contents for Industrial Scientific M40

  • Page 1 c i f , e l • • u r t i t c...
  • Page 2 OUR MISSION Design - Manufacture - Sell: Highest quality products for the preservation of life and property. Provide: Best customer service available.
  • Page 3 Dear Valued Customer, Thank you for buying and using Industrial Scientific’s M40 Multi-Gas Monitor. Your M40 can be relied upon for dependable service, day after day. It has been designed, manufactured, tested and proven under the most scrutinizing conditions possible.

  • Page 4: Table Of Contents

    Oxygen deficient atmospheres may cause combustible gas ..............7 readings to be lower than actual concentrations. NSTRUMENT PERATION M40 Gas Reading Mode............7 Oxygen enriched atmospheres may cause combustible gas Operating Modes ..............8 readings to be higher than actual concentrations. Zero/Calibration Mode ............9 Display Peaks Mode ............9...
  • Page 5 Carrying case ACCURACY MAY BE CORRECTED BY REFERRING TO THE ZERO/CALIBRATION SECTION OF THE INSTRUCTION MANUAL. 1810-5460* SP40 sampling pump THE MODEL M40 IS CERTIFIED FOR USE WITHIN AN AMBIENT 1810-5999* Carrying case TEMPERATURE RANGE OF -20°C TO 40°C ONLY. 1711-6096*...

  • Page 6: Introduction

    Configuration Mode. When the countdown is complete, the M40 will be in its normal Gas Reading Mode. To turn off the M40 instrument press and hold the button for 5 seconds.

  • Page 7: Operating Modes

    ODES ALIBRATION Pressing the arrow key once from the Gas Reading Mode will put the M40 in the Zero/Cal Mode. When this Zero/Callibration mode is entered, the "Zero" icon and the "Enter" icon will Mode be displayed along with all four gas readings. Pressing the arrow key a second time will advance you to the Display Peaks Mode.

  • Page 8: View Twa Mode

    If no changes are needed, press the arrow code has been set ( 000 ), the M40 will go directly to the key to move to the next screen. If changes are desired, low alarm setpoints. If a security code has been set, use press the key.

  • Page 9: Twa Alarm Set Points

    Continue this process until all four high alarm set points STEL A LARM OINTS have been set. Once all four values are set, the display will STEL The fourth of the configuration screens is the STEL alarm again show the "Buzzer", "High", "Enter", and values.

  • Page 10: Calendar Setting

    The calibrate the instrument when a security code is set. For current security code will be flashing. To adjust the first more information on how to calibrate the M40, please see value, use the arrow keys. Once the the Zero/Calibration section.

  • Page 11: Zero /Calibration

    To clear the LEL over range, power down replaced. Full span values less than 50 percent will result the M40 and restart it. After any over range it is good practice to in a failed calibration. To abort calibration at any point in verify the calibration of the combustible gas sensor.

  • Page 12: Maintenance

    M40's battery pack. The pump attaches to the Rechargeable Lithium-Ion battery M40 via two captive screws on the face of the M40. The SP40 has a flow rate of .5 3.6 Volts, 1.8 Amp/hr.

  • Page 13: Replacement Parts List

    INCLUDING STRICT LIABILITY IN TORT. = 2 (European plug) = 3 (Australian plug) It shall be an express condition to Industrial Scientific’s warranty that all products be carefully inspected for damage by Buyer upon receipt, be properly calibrated for Confined Space Kits Buyer’s particular use, and be used, repaired, and maintained in strict accordance...
  • Page 14 It is expressly agreed by the parties that any technical or other advice given by Industrial Scientific with respect to the use of the goods or services is given without charge and at Buyer’s risk; therefore, Industrial Scientific assumes no obligations or liability for the advice given or results obtained.

Table of Contents

Save PDF