Related Manuals for Jet JAT-920 505920
Summary of Contents for Jet JAT-920 505920
- Page 1 Pneumatic Riveter #505920, JAT-920 Operation & Parts Manual M-505920 Edition 2 11/2018 427 New Sanford Road LaVergne, TN 37086 Ph.: 800-274-6848 www.jettools.com Copyright © 2015 JET...
-
Page 2: Warranty And Service
Accessories; Shop Tools; Warehouse & Dock products; Hand Tools NOTE: JET is a division of JPW Industries, Inc. References in this document to JET also apply to JPW Industries, Inc., or any of its successors in interest to the JET brand. -
Page 3: Safety Warnings
15. Excessive air pressure and too much free Do not use this tool for other than its intended rotation may decrease life of the tool and may use. If used for other purposes, JET disclaims cause a hazardous situation. any real or implied warranty and holds itself 16. - Page 4 32. Do not lubricate the tool with combustible specifically designed to filter out microscopic liquids, such as kerosene, diesel or jet fuel. particles. more information http://www.p65warnings.ca.gov/ http:// 33.
-
Page 5: About This Manual
As with any tool operation, safety of operator and bystanders should be first priority. If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our web site: www.jettools.com. -
Page 6: Setup And Assembly
Use wrench to unscrew nosepiece counter- Setup and Assembly clockwise. See Figure 2. Any missing parts or damage should be reported immediately to your JET ® distributor. Do not use a damaged tool. Read this instruction manual thoroughly for operation, maintenance and safety instructions. -
Page 7: Maintenance
Maintenance Lubrication The air riveter should be lubricated daily (or before each use) with air tool oil through the air inlet. During continual operation, it should be re-oiled every 1 to 2 hours. This can be done with an in- line oiler, or manually. - Page 8 Use a light oil containing rust inhibitors, such as If it takes more than 8 seconds to tighten or loosen SAE #10. Many JET air tools have integral oil a bolt or nut with an air impact wrench at reservoirs, which should be kept filled when in-line maximum setting, the air wrench is too small or oilers are not used.
- Page 9 Figure 3 Recommended arrangement of air piping and air line system...
- Page 10 Troubleshooting JAT-920 Pneumatic Riveter Any disassembly of the tool should be done by qualified service personnel. For problems not addressed below, contact JET technical service at 800-274-6846. Problem Possible cause Remedy Riveting force insufficient. Air valve obstructed. Clear any obstructions.
-
Page 11: Replacement Parts
Replacement parts Service parts are listed on the following pages. To order parts or reach our service department, call 1-800- 274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Please have the stock number and serial number of your tool available when you call, so that we may serve you quickly and accurately. - Page 12 #505920, JAT-920 Pneumatic Riveter – exploded view JAT-920 Pneumatic Riveter...
- Page 13 #505920, JAT-920 Pneumatic Riveter – parts list Index Part No. Description Index Part No. Description 706-1A Nosepiece 3/16 in. 706-21 Backup O-ring P12 706-1B Nosepiece 5/32 in. 706-22 Frame lock nut 706-1C Nosepiece 1/8 in. 706-23 Rubber cushion 706-1D Nosepiece 3/32 in. 706-24 Air cylinder JAT920-021 Front jaw case...
- Page 14 This page intentionally left blank. JAT-920 Pneumatic Riveter...
- Page 15 This page intentionally left blank.
- Page 16 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.com JAT-920 Pneumatic Riveter...