Table of Contents
Advertisement
Quick Links
MODEL# RG-SB-1 & RG-SB-2 CROWN VERITY SIDE
BURNER OPERATING AND INSTALLATION
RETAIN FOR FUTURE REFERENCE. OBEY ALL SAFETY WARNINGS AND PROCEDURES.
Thank you for purchasing this product. With proper use, the RG-SB-1 & RG-SB-2 side burner will enhance
the outdoor cooking experience for many years. Crown Verity Inc. is proud of this product and we hope
you will enjoy using it.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable
vapors or liquids in the vicinity of this or any
other appliance.
This appliance is for operation outdoors only ANSI Z83.11/CSA 1.8
INSTRUCTIONS
REVISED June, 2016
WARNING:
adjustment, alteration, service or maintenance
can cause property damage, injury or death. Read
the installation, operating & maintenance
instructions thoroughly before installing or
servicing this equipment.
Improper installation,
Page 1 of 8
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for CROWN VERITY RG-SB-1
Summary of Contents for CROWN VERITY RG-SB-1
-
Page 1: For Your Safety
RETAIN FOR FUTURE REFERENCE. OBEY ALL SAFETY WARNINGS AND PROCEDURES. Thank you for purchasing this product. With proper use, the RG-SB-1 & RG-SB-2 side burner will enhance the outdoor cooking experience for many years. Crown Verity Inc. is proud of this product and we hope you will enjoy using it. - Page 2 INSTALLATION The RG-SB-1 (single burner) & RG-SB-2 (dual burner) side burners are offered in built-in version only and are offered in both L.P. and Nat. gas. Units are not supplied with a hose or a regulator, as installations will vary for built-in applications. In all cases, a qualified gas technician should perform the connection of a gas supply line.
- Page 3 CLEARANCES TO COMBUSTIBLE MATERIALS (FIG 1.) RG-SB-2 (Dual Side Burner Shown) Page 3 of 8...
- Page 4 ROUGH-IN DIMENSIONS (FIG 2.) Note: minimum spacing between all BI (Built In) components in any configuration is 3". The gas supply inlet is located at the bottom of the manifold, inside the front of the side burner cabinet. It is pre-fitted with a 3/8" x 45 degree flare fitting and is ready to receive 3/8" flared copper tubing. GAS INLET LOCATION (FIG 3.) RG-SB-2 (Dual Side Burner Shown) Page 4 of 8...
- Page 5 The supply pressure must be regulated according to the pressures indicated on the rating plate. The regulators that are supplied with all Crown Verity gas units are compatible with RG-SB-1 & RG-SB-2 side burners and could be used to regulate gas for the side burners. A ''Tee'' can be installed downstream of the regulator and copper tubing can then be used to connect the side burner.
- Page 6 6. Take care; your side burner is still hot. MAINTENANCE AND CLEANING Very little maintenance is required to keep your RG-SB-1 & RG-SB-2 side burner in top operating condition. Periodic cleaning should be done to the cabinet, grate and the burner head.
- Page 7 IF YOU SMELL GAS: Shut off all burners and pilots on all appliances. Shut off and disconnect all gas supply valves and hoses. Do not operate the appliance(s) until the problem is repaired. If the problem persists, immediately consult your gas installer. Keep the area free of any and all sources of ignition. Instructions to be used in the event that you smell gas, should be posted in a prominent location.
- Page 8 THE FOLLOWING MUST BE CHECKED: Cylinder valve including threads into tank. • All cylinder welds. • • Regulator fitting(s) and cylinder connections. All hose connections. • All valve connections. • Procedure 1. Open the gas supply valve to the side-burner. 2.
Need help?
Do you have a question about the RG-SB-1 and is the answer not in the manual?
Questions and answers