Genelec S360A Operating Manual page 3

COMPUTER
RUNNING
GLM SOFTWARE
USB CABLE
Figure 1. GLM control network cabling
TONE CONTROLS
+2
ALL OFF
0
-2
BASS
-4
TILT TREBLE
-6
DESKTOP TILT
dB
BASS
ROLL-OFF
20 160 800 4k 20k
Frequency (Hz)
MAINS INPUT GLM
50 / 60 Hz 200 W
NETWORK
100 - 240 V~
WARNING: ELECTRIC SHOCK HAZARD. DO NOT OPEN. DO NOT SUBJECT TO
WATER OR MOISTURE. NO USER SERVICEABLE PARTS INSIDE. REFER
MAINS
SERVICING TO QUALIFIED PERSONNEL. USE EARTHED MAINS CONNECTION
S360A ONLY.
AVERTISSEMENT RISQUE DE CHOC ÉLECTRIQUE. NE PAS OUVRIR. NE PAS
EXPOSER À L'EAU OU L'HUMIDITÉ. AUCUN COMPOSANT À L'INTÉRIEUR
CONNECTOR
REMPLAÇABLE PAR L'UTILISATEUR. ADRESSER TOUTE RÉPARATION À UN
PERSONNEL QUALIFIÉ. CET APPAREIL DOIT ÊTRE RACCORDÉ À LA TERRE.
MADE IN FINLAND
LAITE ON LIITETTÄVÄ SUOJAKOSKETTIMILLA VARUSTETTUUN PISTORASIAAN.
www.genelec.com APPARATET MÅ TILKOPLES JORDET STIKKONTAKT.
APPARATEN SKALL ANSLUTAS TILL JORDAT UTTAG.
SERIAL NUMBER
This device complies with FCC Part 15 and Canadian ICES-003 radio frequency
Class B emission requirements. Refer to operating manual for full information.
GLM NETWORK
CONNECTORS
Figure 2. Connectors and local controls on the back panel
of a S360A.
The setup is fast and consists of the following steps:
1. Connect a CAT5 (RJ45) or higher category cable between
each monitor (and subwoofer) and finally to the control
network input of the GLM Adapter device (see Figure 1).
2. Connect the GLM Adapter device to computer USB
connector.
3. Using a microphone stand, place the Genelec measurement
microphone at the listening location with the microphone
pointing upwards and the microphone top at the height of
the engineer's ear. The microphone is a part of the GLM
User Kit.
4. Connect the microphone cable to the microphone input in
the GLM Adapter device.
THE LISTENING
GLM ADAPTER
GLM TERMINATOR
MONITORS
FUNCTION SWITCHES:
- LED DISABLE
- ISS
- DIGITAL A/B
- LEVEL SENSITIVITY
- STORED CONTROL
ON
-4
-2 -6
0 dBu
OFF
+2 +6 POWER/RESET
+4
SENSITIVITY RESET TO FACTORY
SWITCH
IN dBu FOR SETTINGS: PUSH
100 dB SPL (1 m)
BUTTON FOR 10 SEC
DIGITAL IN DIGITAL THRU ANALOG
DIGITAL IN,
AES/EBU AES/EBU IN
DIGITAL THRU AND
ANALOG IN
CONNECTORS
MICROPHONE
PLACED IN
POSITION
GLM NETWORK
CABLE
Figure 3. Connector panel detail.
5. Download the GLM software at the Genelec web site (www.
genelec.com).
6. Install the GLM software and follow the instructions in the
software to measure and set up your monitors.
7. If you plan to not use a computer for controlling the
monitors, use the GLM software to write the setting into the
monitors (use menu item "Group | Store Group Settings").
GLM calculates the acoustic compensation for the room in a
cloud computer. This enables always up-to-date methods and
efficient calculation process. The Stored Settings function using
the Genelec Loudspeaker Manager software can be used to
store calibration settings into the monitors.
Once the GLM network is disconnected, the calibrated stored
settings using the Genelec Loudspeaker Manager software can
be selected in use by setting the STORED switch to the ON
position found on the rear of the monitor.
3