Advertisement
FORD SUPERDUTY INSTALLATION
(800) 338-3697 toll free
(360) 736-9992 fax
www.pace-edwards.com
Pace Edwards Company
2400 Commercial Blvd
Centralia WA 98531
SWF2-1808
SERIES RETRACTABLE TRUCK BED COVERS
INSTRUCTIONS
TABLE OF CONTENTS
Tools Required for Assembly ........................................................
Before You Start .............................................................................
Drain Hole Locations .....................................................................
1. Remove Packaging Plywood & Hardware Packaging ........
2. Positioning Canister ...............................................................
3. Installing Rails .........................................................................
4. Installing Clamps ....................................................................
5. Installing Kickstands ..............................................................
6. Lubricating & Placing Sweep Seals ......................................
7. Installing Drain Tubes ...........................................................
8.
Installing Top Cover & Velcro ..........................................................
Operating Instructions ..................................................................
Helpful Maintenance Hints ..........................................................
Warranty Statement .....................................................................
2
2
2
2
3
3
3
4
5
5
5
6
6
7
INSTALLATION INSTRUCTIONS
Advertisement
Related Manuals for Pace Edwards SWITCHBLADE SW 2069
Summary of Contents for Pace Edwards SWITCHBLADE SW 2069
-
Page 1: Table Of Contents
2. Positioning Canister ………….……………………………….…………. www.pace-edwards.com 3. Installing Rails ……………..……...…………………………….…………. 4. Installing Clamps ………………………...…………….……….………... 5. Installing Kickstands …………………...……………………………….. Pace Edwards Company 6. Lubricating & Placing Sweep Seals .…..………………………….. 7. Installing Drain Tubes …………………….…..……………………….. 2400 Commercial Blvd Installing Top Cover & Velcro ……………………..………………………….. -
Page 2: Tools Required For Assembly
TOOLS REQUIRED FOR ASSEMBLY: Tape Measure Utility Knife 7/16” Wrench or Socket Side Cut or Needle Nose Pliers #2 Phillips Screwdriver Note: There should be no drilling into the truck body needed on most standard or full-size trucks. BEFORE YOU START: Read the instructions carefully before you start. -
Page 3: Installing Rails
STEP 2: POSITIONING THE CANISTER Use the Pull-strap and one canister flange to lift and steady the Place the Canister in the truck bed just behind the cab unit. Wrap the Pull-strap around the canister of the canister a and center it from side to side. Ensuring that the canister couple of times and double it up in your hand. - Page 4 STEP 4: INSTALLING THE CLAMPS Secure the rails to the truck bed by installing two clamp assemblies per rail. Slide the Clamp Grip onto the Rail at the Clamp Relief and then slide it towards the Rail Bracket and Shim (Fig 4E and 4F). Then assemble the rest of the clamp parts as shown below (Fig 4C & 4D). Be sure to use the long clamp grip at the canister end (FIG 4D) and the shorter clamp grip at the tailgate end (FIG 4C).
- Page 5 STEP 6: INSTALLING THE KICKSTANDS Install the kickstands at the tailgate ends of the rails (FIG. 6A). Loosely fasten the kickstand assembly to the clamp grip, on the side of the grip where the pivot foot will land on the flattest section of the bed wall. Rotate the assembly so that the kickstand will push as squarely as possible against the bed wall (FIG.
- Page 6 STEP 8: INSTALLING THE DRAIN TUBES First, ensure that the Foam Washer is in place on the Drain Fitting as this washer will FIG. 8A help prevent water leakage. Next, test fit the drain tube to determine the length you want to trim it.
-
Page 7: Operating Instructions
However, you should not wax your cover. Using a citrus-based vinyl cleaner and protectant such as Pace Edwards’ UV Protectant (or 303 brand protect- ant) will keep your cover looking like new. To assure quiet, smooth operation, periodically apply a generous amount of the same Pace-Edwards’... - Page 8 1-800-338-3697 to determine warranty eligibility. In either event, it is the responsibility of the purchaser to obtain a Return Goods Authorization prior to returning the defective part to the MFG. The defective part, along with a copy of the original Bill of Sale and the Pace Edwards issued RGA #, must be returned PREPAID to Pace Edwards Co. 2400 Commercial Blvd. Centralia, WA 98531. After determining the validity of the warranty claim, PACE EDWARDS will ship a replacement part prepaid to the customer.