Page 1
HPH Series J-Hook Installation Instructions...
Page 2
Mounting to a vertical surface: HPH16, HPH32, HPH48 and HPH64 Use a nail*, bolt* or screw* with a minimum head diameter of 0.329” (Fig.1-A) and an appropriate length for the substrate (Fig.1-B) to fasten the HPH J-Hook (Fig.2) to the vertical surface (Fig.3).
Page 3
Mounting to a rod or ceiling wire with a Multi-Function Clip-Batwing: HPH16W, HPH32W, HPH48W and HPH64W HPHXXW J-Hooks (Fig.1) are pre-assembled to Multi-Function Clip-Batwings at the factory using a fastener such as a rivet or a zinc plated ¼-20 x 3/8” pan head Phillips machine bolt and a grade A ¼-20 hex Nylon locknut (Fig.2).
Page 5
A ¼-20 hex Nylon locknut (Fig.3). A plain HPH J-Hook may be assembled to a Platinum Tools Angle Clip 90° in the field using a similar fastener. Fasten the HPHXXAC or HPHXXAC6 to 1/4" or 3/8” threaded rod using two standard hex nuts (Fig.4). Thread a single nut up to the desired location of the threaded rod.
Page 7
Mounting to a horizontal surface with an Angle Clip 90° w/Powder Actuated Nail (PAN): HPH16ACPA, HPH32ACPA, HPH48ACPA and HPH64ACPA Use a powder actuated tool* to install the 1-5/16” pin into an appropriate material such as concrete as shown in Fig. 3 & 4. Fig.1 Fig.2 Fig.3...
Page 8
Mounting to a beam with an HOK24 or HOK58 Hammer-On Beam Clamp: HPH16HOK24, HPH16HOK58, HPH32HOK24, HPH32HOK58, HPH48HOK24, HPH48HOK58, HPH64HOK24 and HPH64HOK58 Secure a Hammer-On Beam Clamp to a flange using a hammer as shown in Fig. 5 & Fig. 6 below.
Page 9
Mounting to a beam with an FM24 or FM58 Hammer-On Beam Clamp: HPH16ACFM24, HPH16ACFM58, HPH32ACFM24, HPH32ACFM58, HPH48ACFM24, HPH48ACFM58, HPH64ACFM24 and HPH64ACFM58 Secure a knock-on beam clamp to a flange using a hammer as shown in Fig. 5 & Fig. 6 below. Note: The ACFM24 is designed for flanges from 1/8"...
Page 10
Mounting to a beam with a BC Beam Clamp: HPH16BC, HPH16ACBC, HPH32BC, HPH32ACBC, HPH48BC, HPH48ACBC, HPH64BC and HPH64ACBC Secure a screw-on beam clamp to a flange using a 3/8” socket driver or wrench as shown in Fig.5, 6, 7, & 8 below. Tighten the bolt to 20 in-lb. Note: The BC &...
Page 11
Fig.7 Fig.8 Mounting to a beam with an SSBC Spring Steel Beam Clamp: HPH16SSBC, HPH16ACSSBC, HPH32SSBC, HPH32ACSSBC, HPH48SSBC, HPH48ACSSBC, HPH64SSBC and HPH64ACSSBC Secure a screw-on beam clamp to a flange using a 3/8” socket driver, wrench or Phillips head screw driver as shown in Fig. 5, 6, & 8 below. Tighten the bolt to 20 in-lb. Note: The SSBC &...
Page 12
Fig.5 Fig.6 Fig.7 Fig.8 Part No. Fig. UL Load Designed Description Rating Size LBS. | flanges HPH16SSBC 1" 1 & 2 88.96 1” Spring Steel Beam Clamp HPH J-Hook, size 16 1” Swivel 360° Spring Steel Beam Clamp HPH HPH16ACSSBC 1”...
Page 13
Mounting to a joist with an Angled Overhang (AO) or Vertical Overhang (VO) spring steel clip: HPH16AO, HPH16VO, HPH32AO, HPH32VO, HPH48AO, HPH48VO, HPH64AO and HPH64VO Secure an AO spring steel “Z” purlin clip or a VO14 “C” purlin clip to a joist using a hammer as shown in Fig.
Page 15
Mounting to threaded rod with a female threaded eye coupling: HPH16EH, HPH32EH, HPH48EH and HPH64EH Thread the eye coupling on to ¼-20 threaded rod as shown in Fig. 3, 4 & 5 below. Fig.1 Fig.2 Fig.3 Fig.4 Fig.5 Part No. Hook Fig.