Advertisement
TAPEPRO FLATBOX
The Tapepro Flatboxes are designed to apply the correct amount of joint compound over taped, flat
joints when used in conjunction with a Tapepro Flatbox Handle. The Tapepro Loading Pump and Flat
Box Filler Nozzle are also available to make filling your flatbox quicker and easier. The Tapepro range of
tools and parts is also compatible with the Premier Drywall Tools and Accessories.
The Tapepro Flatbox range includes:
>
200mm Tapepro Flatbox (second coat)
>
250mm Tapepro Flatbox (finish coat)
>
300mm Tapepro Flatbox (finish coat)
BEFORE USE
>
Make sure the Tapepro Flatbox blade is the thickness of a fingernail (1 – 1.5mm)
above the skids. The blade can be adjusted using screws on the blade holder to
obtain the necessary height. (FB-1)
>
Test that the blade holder can move up and down freely.
>
Attach your Tapepro Flatbox Handle by sliding it onto the box and tightening the
two wing nuts.
(FB-2)
>
Adjust the tension on the blade holder to suit the gauge of compound which is to
be used in the machine.
(FB-3)
LOADING
Compound can be loaded into the Tapepro Flatbox either with the aid of a Loading Pump
and appropriate filler nozzle or by hand.
Loading with Pump
1.
Attach the filler nozzle to pump.
2.
Fit the nozzle into the slot on the bottom of the Tapepro Flatbox.
3.
Pump the compound in to the Tapepro Flatbox, moving the box from side to side
while pumping to ensure the compound is evenly distributed. Do not overfill.
4.
Remove any excess compound from around the slot.
Loading by Hand
1.
Open the lid.
2.
Evenly fill the Tapepro Flatbox with compound using a joint knife. Do not overfill.
3.
Close the lid.
4.
Remove any excess compound.
USING THE TAPEPRO FLATBOX
1.
Set the box at a slight angle from the handle and apply the brake so the head
remains stationary.
2.
Place the Tapepro Flatbox on the joint and while applying pressure, release the
brake allowing the box and the handle to find is own natural position.
3.
Run the machine along the joint applying pressure evenly to ensure a consistent
finish.
(FB-6)
4.
Reapply the brake toward the end of the joint.
5.
Remove the box from the wall in a sweeping motion about 300mm from the end of
the joint.
6.
Using the same technique, turn around, and coat the remaining 300mm of the joint.
(FB-7)
(FB-4)
(FB-5)
Tip: The Tapepro Flatboxes can reach even higher with the addition of a Tapepro
Handle Extension. The Tapepro Handle Extensions are threaded and fit easily in to
both Tapepro and Premier Flatbox Handles.
CLEANING
Your Tapepro Flatbox should be cleaned after every use to maximise lifespan and maintain
optimal performance.
FB-1
Remove any compound from your Tapepro Flatbox with a hose and stiff brush. The Tapepro
Flatbox can be dismantled for a more thorough clean when required.
MAINTENANCE
All replacement parts are available from your local plasterboard distributor or Tapepro
FB-2
Drywall Tools. For your nearest distributor please visit our website: www.tapepro.com or
call Tapepro Drywall Tools on +61 7 5520 6022.
General Maintenance
To protect and lubricate your Tapepro Flatbox, use a silicon spray. Do not use solvents to
clean your Flatbox as they will damage the wiper seals and reduce performance.
Regular wear parts should be replaced as needed.
FB-3
Flatbox Blade
If the Tapepro Flatbox Blade cannot be adjusted to the required height it will need to be
replaced by following these simple steps.
1.
Tighten the screws on the blade holder so that the blade is forced out of the blade
holder groove.
(FB-10A)
2.
Remove the blade from the blade holder. If there is resistance, a screwdriver can
be used to gently lever it out.
FB-4
3.
Remove all dry joint compound from under the blade and in and around the blade
holder using a wire brush.
4.
Bend the new blade into a slight 'w' shape, this keeps the blade secure.
5.
Adjust the screws on the blade holder so the blade is the thickness of a fingernail
(1-1.5mm) above the skids.
Tapepro Flatbox Blade).
FB-5
Tip: Maintaining and replacing wear parts is made easy with the Tapepro Flatbox
Maintenance and Service Kits.
(FB-11)
WARRANTY
All manufacturing faults are covered under warranty. All non wear parts are covered under
FB-6
a 3 year warranty.
(FB-8)
(FB-9)
(FB-10B)
(FB-10C)
(refer to illustration from 'before use' regarding the width of the
FB-7
FB-8
FB-9
FB-10A
FB-10B
FB-10C
FB-11
Advertisement
