Advertisement
1
D
Hold the entry in position with a spanner/wrench to
prevent rotation. Hand tighten the middle nut to the
entry and turn a further ½ to ¾ of a turn with a
spanner/wrench.
IMPORTANT: Support the cable to prevent it from
twisting.
CABLE GLAND SELECTION TABLE
Male Entry
Outer Sheath
Size
Thread Size
Ref.
Metric
NPT
Min.
A
M20
½" - ¾"
12.5
B
M25
¾" - 1"
16.9
C
M32
1" - 1¼"
22.0
CABLE GLAND SIZE FOR CONDUCTOR
Maximum No.
of Cores
1.5
7
A & B
4
---
3
---
ACCESSORIES:
Before cable gland assembly or stripping of the cable gland
assembly, consideration should be given to any cable gland
accessories that may be required, such as: -
Shroud, to offer additional corrosion protection.
Locknut, to secure cable glands into position.
Sealing washer, to offer additional ingress protection of the
enclosure at the cable gland entry.
Earthtag, to provide an external armour/braid bonding point.
Serrated washer, to dampen any vibrations that may loosen the
locknut or cable gland assembly.
SCHEDULE OF LIMITATIONS:
1. The cable glands when used with braided cable types are only
suitable for use with fixed apparatus, the cable for which must
be effectively clamped and cleated elsewhere.
2. This cable gland has an operating temperature range of -60°C
to +80°C.
3. A seal must be formed between the equipment and the cable
gland to maintain the appropriate degree of protection against
ingress of dust, solid objects and water.
AI 312 - Issue R / Page 2 of 2
6
2
E
Unscrew the middle nut and visually inspect that
the armour/braid has been successfully clamped
between the armour spigot and the armour
clamping ring . If armour/braid not clamped, repeat
assembly.
Note : If the equipment has a threaded entry, it may be
advisable to screw the cable gland into the equipment to
prevent twisting of the cable after Step E
Steel Wire Armour/
Tape/Braid
Orientation
Orientation
Max.
1
2
20.5
0.8/1.25
0/0.8
26.0
1.25/1.6
0/0.7
33.0
1.6/2.0
0/0.7
Cores Cross Sectional Area mm²
2.5
4.0
6.0
A & B
B & C
C
---
---
B
---
---
---
6
4
3
2
1
Hexagon
Dimensions
Across
Across
Flats
Corners
53.0
80
30.0
69.5
88
36.0
64.0
95
46.0
10.0
PUNCH TOOL SIZE DETAILS
C
---
Punch Ref.
B
Core C.S.A. mm²
EU Declaration of Conformity in accordance with European Directive 2014/34/EU
Manufacturer: Hawke International
Address: Oxford Street West, Ashton-under-Lyne, OL7 0NA, United Kingdom.
Equipment: Group II Compression Cable Glands Type: PSG 553/RAC
Provisions of the Directive fulfilled by the Equipment:
Group II Category 2GD Exeb IIC Gb, Exdb IIC Gb, Extb IIIC Db – IP66
Notified Body for EU-Type Examination: SGS-Baseefa 1180 Buxton UK
EU-type Examination Certificate: Baseefa06ATEX0056X
Notified Body for production: SGS-Baseefa 1180 Buxton UK
Harmonised Standards used:
EN60079-0:2012+A11:2013, EN60079-1:2014, EN60079-7:2015, EN60079-31:2014.
On behalf of the above named company, I declare that, on the date the
equipment accompanied by this declaration is placed on the market, the
equipment conforms with all technical and regulatory requirements of the above
listed directives.
......
......
......
......
.........
...
........................................
...
...
...
...
...
...
...
...
...
...
...
...
...
............
A. Tindall
Technical Manager
F
Select the correct punch tool to suit the
conductors sizes (see table) and cut out the
required number of holes in the seal using the
indented positions as a guide. Remove the entry
and pass the individual conductors through
the appropriately sized punched holes in the seal
ensuring they are not twisted or kinked, and
slide the seal down to the spigot .
Replace entry and re-assemble middle nut
onto the entry component .
Tighten up the middle nut until hand tight,
then using a wrench/spanner turn the nut
through a minimum of one full turn.
Hand tighten the backnut to form a seal
32.5
around the cable, then tighten a further full turn
39.5
using a wrench/spanner. Ensure that the middle
nut does not rotate when tightening the
50.5
backnut . Ensure that the deluge seal is pulled
down into position, if fitted.
Locate the shroud over the cable gland, if
applicable.
No.1
1.5 - 2.5
4.0 - 6.0
6
5
2
1
No.2
No.3
10.0
Advertisement
