AMX RE-DM6 Quick Start Manual

Overview
The RE-DM6 RADIA Eclipse 6-Channel Integrated Dimmer Module (120V: FG706-03;
240V: FG706-04) controls up to six circuits with six 1200-watt onboard dimmers
(FIG. 1). The RE-DM6 is designed for use with the RDA series of enclosures, in an AMX
Lighting™ modular digital dimming system. The RE-DM6 is controlled by AxLink or by
dry (contact) closures.
Power Devices
Jumper
High Voltage
Connections
Load out
CLASS 1 WIRING
CLASS 2 WIRING
AxLink Address
DIP Switch
AxLink Connector
FIG. 1 RE-DM6 6-CHANNEL INTEGRATED DIMMER MODULE
Specif ications
RE-DM6 SPECIF ICATIONS
Dimensions (HW): 5.75" x 10.0" (146.05 mm x 254.00 mm)
Weight: 4.5 lbs (2.04 kg)
Line input: • 120, 240 VAC, single phase, 2W+G, 50/60 Hz, 2400 W, one feed
• 120, 120/240, 240 VAC, single phase, 3W+G, 50/60 Hz,
4800 W, dual feed
Output: • 1200 W max. per channel @120, 240 VAC
• 2400 W max. total, all 6 channels on with single 2400 W feed
• 4800 W max. total, all 6 channels on with dual 2400 W feeds
• Line input #1 goes to dimmer 1, 3, and 5; line input #2 goes to
dimmer 2, 4 and 6
• All electrical ratings are for continuous duty
Wire rating: Use only copper wires rated at 75°C (167°F) min.
Torque terminals: To 20 in-lbs (2.3 N/M)
Maximum wire size: 10 AWG (4 mm²)
Wire stripping length: 0.5" (13 mm)
AxLink Port: 4-pin 3.5mm green captive wire connector - AxLink
communication signaling with 12VDC power in.
Aux Power: 2-pin 3.5mm green captive wire connector. This is a 12VDC power
input that supplies additional power to the Radia PCB and
connected Radia modules.
Dry Contacts: • Emergency fire alarm relay connection - Closed relay activates
preset 126. Other control is locked out until relay opens.
Supports daisy chaining of up to 20 dimmers for this
connection, with a maximum current requirement of 200mA
when daisy-chained.
• Failsafe connection - Works with a toggle switch - opening the
switch triggers preset 128, closing the switch triggers preset
127. Supports daisy chaining of up to 20 dimmers for this
connection with a maximum current requirement of 200mA
when daisy-chained.
BTU/hr: 300 single feed (2400 W); 600 dual feed (4800 W)
RE-DM6
Mounting points (x4)
Line In
Neutral
Chokes
External +12
Aux Power
4-Pin Connectors to
RDM Series Modules
Dry Closures
Radia Eclipse 6 Dimmer Module (120 VAC/240 VAC)
RE-DM6 SPECIF ICATIONS (CONT.)
Idle current draw: 75 mA @ 120 VAC, 50 mA @ 240 VAC, 100 mA @ 13.5 VDC
Certifications: • FCC
• CE
• UL North America
• IEC-60950 Safety
Operating Temp Range: 0° to 40°C (32° to 104°F)
Included Accessories: • 2 4-pin captive 3.5mm wire connectors (41-5047)
• 4 #8-32x1/2" F-point mounting screws
Required Enclosures: • RDA-ENC2 (FG606-10)
• RDA-ENC4 (FG606-11)
• RDA-ENC6/6B (FG606-12/13/15)
• RDA-ENC12B (FG606-14/16)
Suggested Installation Loads
DIMMED SWITCHED
Incandescent Motors
Neon, cold-cathode Fans
Caution: Pre-Installation Notes
WARNING: This unit should be installed only by qualif ied electrical personnel, and in
compliance with all national electrical codes, local codes and ordinances. To prevent
possible personal injury or death, disconnect power to the enclosure at the breaker box
before attempting to work with any AMX Lighting modules.
• All Class 1 and 2 wiring must be connected to their dedicated terminals.
• Class 1 wiring should be connected through the top of the enclosure, and Class 2
wiring through the bottom.
• Load conductors must be same size as line conductors, regardless of connected
load.
• Disconnect power while installing or connecting the unit.
• Keep top and bottom air vents clear at all times, and maintain 12" (30.48 cm)
clearance around the top and bottom.
• Test loads for shorts before connecting.
• Class 2 wiring must be rated 300V or higher.
• For indoor use only.
• AC lighting loads only.
• For more information, refer to the RE-DM6 instruction manual available at
www.amx.com.
Radia Lighting System Conf iguration Pages
The AMX Radia Web pages provide a simple interface for users of the Radia Duet
module. The web pages reside on the AMX master when running the Radia Duet module
and may be accessed through Internet Explorer or Mozilla Firefox. The RE-DM6 may
also be configured using NetLinx code or a terminal. For more information, refer to the
RE-DM6 instruction manual available at www.amx.com.
High-Voltage Connections
Each AMX Lighting module has its high-voltage connectors marked on its circuit board.
Line, load, and neutrals are also clearly marked.
HIGH-VOLTAGE CONNECTIONS
FIG. 2
Line-in Connections
• Using two feeds for Line 1 and Line 2 provides two 2400 W inputs.
• Jumping Line 1 and Line 2 provides a single 2400 W input (FIG. 3).
FIG. 3 LINE-IN CONNECTIONS
QUICK START GUIDE
Load
Line in
Load
Neutral
Dual 2400 W Inputs without jumper
Single 2400 W Input with jumper