Advertisement
1.
Set up
Approximate time: 10 minutes
Please note that your U-verse TV and Internet services will not operate during this process.
This includes recording TV shows.
A.
B.
Unplug power cord from existing
Transfer one connection at a time
•
•
Wi-Fi Gateway
from the existing Wi-Fi Gateway
to new Wi-Fi Gateway
Set power cord aside
•
Stand new Wi-Fi Gateway side-by-
•
side with existing Wi-Fi Gateway
Below is a completed setup. Your connections may vary.
New Wi-Fi Gateway
Existing Wi-Fi Gateway
C.
Remove yellow power sticker
•
covering the Power port of new
Wi-Fi Gateway
Connect new power cord to
•
power port of new Wi-Fi Gateway
and into electrical outlet
Wall Jack
B
Green
Data Cable
B
Yellow
Ethernet Cable
(U-verse TV
Customers Only)
B
Yellow
Ethernet Cable
Wireless
Access Point
(Back)
and/or
DVR
(Not Shown)
C
New Power
Cord
Electrical
Outlet
2.
Power up
Approximate time: 1-15 minutes
Your Wi-Fi Gateway is now powering up. During this time (up to 15 minutes),
do not unplug the power cord or the green data cable, as this can permanently
damage the Wi-Fi Gateway and significantly delay your service activation.
A.
When complete, the Service light will begin flashing, then turn to solid green.
If the Service light does not turn solid green or continues to blink after 15 minutes,
Need More Help?
see
on the back of this guide.
B.
For U-verse TV, restart your TV receivers after the Service light is solid green.
Go to each TV and hold down the Power button on the U-verse receiver and
DVR for ten seconds.
NOTE: Live TV may take a few minutes to display. If TV does not respond refer to
Need More Help?
on the back of this guide.
3.
Go Wi-Fi
Approximate time: 10 minutes
New! Transfer Wi-Fi Settings (Network Name and Password) from existing Wi-Fi Gateway to your new
Wi-Fi Gateway so that all your Wi-Fi connected laptops, tablets, and other devices still work.
A.
Select only one option to begin the Wi-Fi Setup
Connect using PC
or Connect using Tablet
(recommended)
Establish a temporary connection
•
Connect laptop or PC
using new Wi-Fi settings located on
•
with an Ethernet Cable
yellow sticker on new Wi-Fi Gateway
B
Continue to
Select your Wi-Fi network (SSID)
•
•
Enter Wi-Fi Password
•
(Wireless Network Key)
Continue to
•
B.
Open a browser and go to http://ufix.att.com/restore
•
Log into your U-verse account with your Member ID (primary AT&T email address) and Password
•
Follow the on-screen instructions to transfer the existing Wi-Fi settings
•
Once Complete:
Record existing Network Name and Wi-Fi Password on separate
•
yellow sticker from kit
Place new yellow sticker over your new Wi-Fi Gateway's
•
yellow sticker
Existing Wi-Fi Settings did not transfer:
Use settings from new Wi-Fi Gateway's yellow sticker
•
Open your device's Wi-Fi connection settings and select your Wi-Fi Network Name
•
Enter Wi-Fi Password to connect to your network
•
Record and keep your Wi-Fi settings for future reference when connecting all your Wi-Fi devices
•
NOTE: Any custom settings made for security cameras or game consoles, etc.,
on your original Wi-Fi Gateway will also need to be made to your new Wi-Fi Gateway.
4.
Easy Return
(Refer to return instructions in your kit)
A.
Take original gateway and power cord to
nearest The UPS Store (Bring your AT&T
Account number located on your packing slip).
Please do not return other devices (e.g. backup battery, etc.)
NOTE: Do not return the Wireless Access Point if you are returning one or more
wireless TV receivers.
Get the most from AT&T GigaPower - att.com/GigaPowerSupport
New Wi-Fi Gateway indicator
lights on front panel. Lights
may vary with setup.
or Connect using Smartphone
Mobile internet access required
•
B
Continue to
•
B
B.
UPS will scan your equipment,
provide a receipt, pack, and ship
equipment to AT&T at no cost to you.
Advertisement
