Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
FOR UNDER CABINET VENT-A-HOODS
WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
A. Installation Work and Electrical Wiring Must Be Done By
Qualified Person(s) In Accordance With All Applicable
Codes And Standards, Including Fire-Rated Construction.
B. When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
C. Ducted fans must always be vented to the out-
doors.
WARNING - TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
Read and Save These Instructions
All Hoods Should Be Installed By A Qualified Installer
————————————————————-
A. Model B100 — Use template provided.
————————————-
A. Attach securely to bottom of cabinet with screws provided.
6”
B100 Single
Blower
C L
of Collar
C L
————————————————————-
A. Model B100: 6” duct or the
equivalent must be installed
throughout.
Step 1.
C L
of Hood
Step 2.
Install canopy in position under cabinet.
——
6”exhaust collar is 3 ” left of
center. Offset Kit VP529 or VP550
are available to bring duct back to
centerline.
of Hood
Motor Cooling
Vents
6” dia.
9”
C L
of exhaust collar
Step 3.
Blower
B100 Single 300 CFM
B200 Dual 600 CFM
Do not restrict ducting anywhere including roof jacks or wall louvers. Don’t
make sharp turns with ducting. Make gradual turns or 45° angles.
Turn Page For More Instructions
D. Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of fuel
burning equipment to prevent back drafting. Follow the
heating equipment manufacturer’s guideline and safety
standards such as those published by the NationaI Fire
Protection Association (NFPA), and the American
Society for Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and local code authorities.
Cut out cabinet.
——
B. Model B200 — Mark cabinet per sketch.
*Make sure cutout is large enough for motor cooling vents.
(Motors are cooled from above).
C L
of Hood
3
8
Wiring
1
5 ”
8
3
3 ”
Front
8
C L
of mounting plate
Connect ducting.
——
Minimum Round
Square
Duct Size
Inches
28
6” (or equivalent)
8” (or equivalent)
50
————————————————————
11
1
” from back
L C
16
of Hood
edge of hood
Motor Cooling
Vents
7
” hole for
8
electric
Cutout
————————————
B200 Dual
Blower
C L
of Hood
———————————————————
B. Model B200: Transition to 8”
round is provided. 8” duct or the
equivalent must be installed
throughout.
1” from back
edge of hood
8”
6”
C L
of Hood
3
2 ”
8
9”
Advertisement
Related Manuals for VentAHood B100 Single 300 CFM
Summary of Contents for VentAHood B100 Single 300 CFM
-
Page 1: Read And Save These Instructions
A. Model B100: 6” duct or the Square Duct Size Blower Inches equivalent must be installed round is provided. 8” duct or the B100 Single 300 CFM 6” (or equivalent) throughout. equivalent must be installed throughout. B200 Dual 600 CFM 8” (or equivalent) Do not restrict ducting anywhere including roof jacks or wall louvers. - Page 2 Step 4. Connect electrical. ———————————————————- —— ——————————————————— Follow abel instructions and remove motor plate. Unplug motor and remove, being careful to not damage blower wheel. Connect electrical, black to black, white to white and ground to lug provided. Hoods with multiple blower units require separate electrical connections. Replace motor(s) and don’t forget to plug them back in.