Packing List - AEG AFNDA18 Original Instructions Manual

operation as accidental actuation may occur, possibly
causing injury.
■ Choice of triggering method is important. Check manual for
triggering options.
■ Do not point the tool toward yourself or anyone whether it
contains fasteners or not.
■ Do not actuate the tool unless you intend to drive a fastener
into the workpiece.
■ Keep fingers away from trigger when not driving fasteners
to avoid accidental firing.
■ During normal use the tool will recoil immediately after
driving a fastener. This is a normal function of the tool.
Do not attempt to prevent the recoil by holding the nailer
against the work. Restriction to the recoil can result in
a second fastener being driven from the nailer. Grip the
handle firmly and let the tool do the work. Failure to heed
this warning can result in serious personal injury.
■ Do not drive fasteners on top of other fasteners or with the
tool at an overly steep angle as this may cause deflection
of fasteners which could cause injury.
■ Do not drive fasteners near edge of material. The workpiece
may split causing the fastener to ricochet, injuring you or a
co-worker. Be aware that the nail may follow the grain of
the wood, causing it to protrude unexpectedly from the side
of the work material.
lOADING TOOl
■ Do not load the tool with fasteners when any one of the
operating controls is activated.
When loading tool:
● Never place a hand or any part of body in fastener
discharge area of tool.
● Never point tool at anyone.
● Do not pull the trigger or depress the workpiece contact
as accidental actuation may occur, possibly causing
injury.
SAvE THESE INSTRUCTIONS
■ Refer to them frequently and use them to instruct others
who may use this tool. If you loan someone this tool, loan
them these instructions also.
ASSEmbly
UNPACkING
This product has been shipped completely assembled.
■ Carefully remove the tool and any accessories from the
box. Make sure that all items listed in the packing list are
included.
■ Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
■ Do not discard the packing material until you have carefully
inspected and satisfactorily operated the tool.

PACkING lIST

■ Angled finish nailer
■ Battery pack
■ Charger
■ Tool bag
8
■ Operator's manual
■ Safety glasses
SPECIFIED CONDITIONS OF USE
You may use this tool for the purposes listed below:
■ Finish and trim (interior and exterior)
■ Door & window casing
■ Door jambs
■ Baseboard
■ Crown molding
■ Cabinetry
■ Cap and shoe molding
■ Molding
■ Staircases
■ Door and window trim
■ Chair rail
■ Brickmold
■ Hardwood flooring
■ Panelling
■ Furniture
OPERATION
bATTERy PROTECTION FEATURES
18 V lithium-ion batteries are designed with features that
protect the lithium-ion cells and maximize battery life. Under
some operating conditions, these built-in features may cause
the battery and the tool it is powering to act differently from
nickel-cadmium batteries.
During some applications, the battery electronics may signal
the battery to shut down, and cause the tool to stop running.
NOTE: To prevent further shut down of the battery, avoid
forcing the tool.
If releasing the trigger and removing and reinstalling the battery
pack does not reset the battery and tool, the battery pack is
depleted. If depleted, the battery pack will begin charging when
placed on the lithium-ion charger.
For complete charging instructions, refer to the operator's
manual for the BL1218 charger. For battery pack instructions,
see the manual for the L1830R, L1815R lithium-ion battery
pack.
TO INSTAll bATTERy PACk
See figure 2.
■ Place battery pack in the tool. Align raised rib on battery
pack with the groove inside the tool.
■ Make sure the latch on the back of the battery pack snaps
in place and battery pack is secured in the tool before
beginning operation.
CAUTION!
When placing battery pack in the tool, be sure raised rib on
battery pack aligns with the bottom of the tool and latches into
place properly. Improper installation of the battery pack can
cause damage to internal components.
8