Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Evolve Power Beam
Summary of Contents for Evolve Power Beam
- Page 1 INSTALLATION GUIDE 2018...
- Page 2 In accordance with the manufacturer’s policy of continual product improvement, the product presented in this document is subject to change without notice or obligation. evolvefurnituregroup.com Evolve Customer Support available at 856.552.4000, 888.827.2500, from 8:30 am - 5:30 pm Eastern time, or fax at 856.552.4001.
- Page 3 “B” into the brackets provided at the top of the raceway, “C” above the slots. STEP 3: Replace the raceway cover. evolvefurnituregroup.com Evolve Customer Support available at 856.552.4000, 888.827.2500, from 8:30 am - 5:30 pm Eastern time, or fax at 856.552.4001.
- Page 4 Two at the bottom, two at the top. STEP 2: Attach the plastic blocks (c) to the bottom, and the spacers (d) to the top of the Power Beam. *The plastic blocks (c) are to be attached with screws, while the spacers (d) come with an adhesive.
- Page 5 STEP 3: Slide it towards the assembly connectors. Be sure the parts are fully seated to assure proper electrical connection and the spring clips are properly engaged for mechanical security. evolvefurnituregroup.com Evolve Customer Support available at 856.552.4000, 888.827.2500, from 8:30 am - 5:30 pm Eastern time, or fax at 856.552.4001.
- Page 6 STEP 1: Hang the base feed on the slots above the “U” bracket and secure it with the provided zip tie. STEP 2: Run the flexible portion of the feed through the opening in the bottom of the Power Beam.
- Page 7 STEP 2: Slide in the module (b) and attach it to the extension connectors using the clamps (c). STEP 3: Add two plastic spacers (d) on top and snap on the top trim (e). evolvefurnituregroup.com Evolve Customer Support available at 856.552.4000, 888.827.2500, from 8:30 am - 5:30 pm Eastern time, or fax at 856.552.4001.
- Page 8 Install block and screw back using the same screw. It is important to start the installation from the middle panel. Blocks installed Peel off double sided tape evolvefurnituregroup.com Evolve Customer Support available at 856.552.4000, 888.827.2500, from 8:30 am - 5:30 pm Eastern time, or fax at 856.552.4001.
- Page 9 Locate top trim and adjust sideways to the middle of the slot Snap on block Install next top trim while ensuring that both trims are fully aligned evolvefurnituregroup.com Evolve Customer Support available at 856.552.4000, 888.827.2500, from 8:30 am - 5:30 pm Eastern time, or fax at 856.552.4001.
- Page 10 11. Place thin plastic seal in middle of trim Incorrect plastic seal installation Correct plastic seal installation evolvefurnituregroup.com Evolve Customer Support available at 856.552.4000, 888.827.2500, from 8:30 am - 5:30 pm Eastern time, or fax at 856.552.4001.
- Page 11 14. Logo should always be consistently on the same bottom corner. Ensure consistency with having the shiny sides of the privacy glass on the same side evolvefurnituregroup.com Evolve Customer Support available at 856.552.4000, 888.827.2500, from 8:30 am - 5:30 pm Eastern time, or fax at 856.552.4001.
- Page 12 2 edges (3/32”) 16. Installation of privacy glass is complete with shiny side out and log on the bottom left corner evolvefurnituregroup.com Evolve Customer Support available at 856.552.4000, 888.827.2500, from 8:30 am - 5:30 pm Eastern time, or fax at 856.552.4001.
- Page 13 18. If needed, pull in the opposite direction and check again 19. When installation is fully satisfactory, cut protruding plastic seal with exacto knife evolvefurnituregroup.com Evolve Customer Support available at 856.552.4000, 888.827.2500, from 8:30 am - 5:30 pm Eastern time, or fax at 856.552.4001.
- Page 14 Evolve Furniture Group 17 West Stow Rd. P.O. Box 562 Marlton, New Jersey USA 08053 T 856 4000 888 2500 F 856 4001 evolvefurnituregroup.com • • • • • •...
Need help?
Do you have a question about the Power Beam and is the answer not in the manual?
Questions and answers