Table of Contents
Summary of Contents for Jet DSAN4-1
- Page 1 Operating Instructions and Parts Manual Dual Station Abrasive Notcher Models: DSAN4-1, DSAN4-3 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-756180 Ph.: 800-274-6848 Edition 3 08/2018 www.jettools.com Copyright © 2017 JET...
-
Page 2: Important Safety Instructions
Do not use this machine for other than its 18. Keep visitors a safe distance from the work intended use. If used for other purposes, JET area. Keep children away. disclaims any real or implied warranty and holds itself harmless from any injury that may result 19. -
Page 3: About This Manual
If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our web site: www.jettools.com. -
Page 4: Table Of Contents
11.0 Replacement Parts ............................. 12 11.1.1 DSAN4-1,-3 Dual Station Notchers – Exploded View ................. 12 11.1.2 DSAN4-1,-3 Dual Station Abrasive Notchers – Parts List ..............13 12.0 Electrical Connections, DSAN4 series Abrasive Notcher ................16 12.1 Wiring Diagram for DSAN4-1 (230V-1PH) ..................... 16 12.2 Wiring Diagram for DSAN4-3 (230V 3PH) ..................... -
Page 5: Specifications For Dsan4-Series Abrasive Notchers
= feet per second The specifications in this manual were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations. -
Page 6: Base Mounting Hole Centers
4.1 Base mounting hole centers Figure 4-1... -
Page 7: Setup And Assembly
5.2 Unpacking and locating The DSAN4-1 is pre-wired for 230 volt, single- Inspect contents for shipping damage. Report phase operation. It is recommended that the damage, if any, to your distributor. Do not... -
Page 8: Grounding Instructions
Connect the motor leads to the incoming power Ampere Total length of Volts source, according to the diagram on inside Rating cord in feet cover of motor junction box. Similar diagrams are in sect. 12.0 of this manual. More More Than If using a plug, replace the 230V plug with a Than... -
Page 9: Wheel Grinding
Figure 7-3 Figure 7-1 7.5 Removing/installing rollers 7.3 Wheel grinding Disconnect machine from power source. Remove tension from abrasive belt (J, Figure 7- For safety, gap between table and grinding wheel should not exceed 1/16-inch Loosen hex nuts (K, Figure 7-4) and turn set (1.6mm). -
Page 10: Adjustable Handles
7.7 Adjustable handles Keep notching table and guide shaft areas clean and free of debris. Use a brush to clear The handles (such as C, Figure 7-1) can be adjusted shavings, not bare hands. to more convenient position; lift up handle and rotate it on the pin, then release, making sure it reseats on 9.2 Lubrication pin. -
Page 11: Troubleshooting Dsan4-Series Abrasive Notchers
10.0 Troubleshooting DSAN4-series Abrasive Notchers Table 3 Symptom Possible Cause Correction* Motor will not start. Low voltage. Check power line for proper voltage. Open circuit in motor or loose Inspect all lead connections on motor for connection. loose or open connections. On/Off switch failure. -
Page 12: Replacement Parts
CST. Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately. Non-proprietary parts, such as fasteners, can be found at local hardware stores, or may be ordered from JET. Some parts are shown for reference only, and may not be available individually. -
Page 13: Dsan4-1,-3 Dual Station Abrasive Notchers - Parts List
35 ....DSAN4-1-35 ....Belt Guiding Shaft ..................1 36 ....DSAN4-1-36 ....Lifting Plate ....................1 37 ....DSAN4-1-37 ....Hex Nut with Set Screw (includes #66) ....M16-2.0 ......3 38 ....DSAN4-1-38 ....Graphite Platen ....................1 39 .... - Page 14 84 ....DSAN4-1-84 ....Spring Plunger ............M10x17 ......2 85 ....DSAN4-1-85 ....Motor................ 4HP, 230V, 1PH ... 1 ....DSAN4-1-85SC ..Starting Capacitor (Not Shown) ....... CD60 300μF 300VAC ... 1 ....DSAN4-1-85RC ..Running Capacitor (Not Shown) ......CBB60 60μF 450VAC ... 1 ....
- Page 15 118 .... DSAN4-1-118 .... 2-1/2" Roller ............. Ø2-1/2"x4-1/2" L ... 1 119 .... DSAN4-1-119 .... 2" Roller ..............Ø2"x 4-1/2" L....1 120 .... DSAN4-1-120 .... 1-1/4" Roller ............. Ø1-1/4"x 4-1/2" L ..1 121 .... DSAN4-1-121 .... 1-1/2" Roller ............. Ø1-1/2"x 4-1/2" L ..1 122 ....
-
Page 16: Electrical Connections, Dsan4 Series Abrasive Notcher
12.0 Electrical Connections, DSAN4 series Abrasive Notcher 12.1 Wiring Diagram for DSAN4-1 (230V-1PH) -
Page 17: Wiring Diagram For Dsan4-3 (230V 3Ph)
12.2 Wiring Diagram for DSAN4-3 (230V 3PH) -
Page 18: Wiring Diagram For Dsan4-3 (460V 3Ph)
12.3 Wiring Diagram for DSAN4-3 (460V 3PH) -
Page 19: Warranty And Service
JET sells through distributors only. The specifications listed in JET printed materials and on official JET website are given as general information and are not binding. JET reserves the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason ®... - Page 20 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.com...