Advertisement
1.
Set up
Approximate time: 10 minutes
Please note that your U-verse TV and Internet will not operate during this process. This includes
recording TV shows.
· Unplug the existing Wi-Fi Gateway from the
A.
electrical outlet
· Set the existing power cord aside—do not use
Frame 6
Existing Wi-Fi Gateway
C.
· Move the remaining cables from the existing
Wi-Fi Gateway to the new Wi-Fi Gateway
Yellow Ethernet Ports
Coax Port
Reset
POWER
Existing Wi-Fi Gateway
New Wi-Fi Gateway
· Stand the new Wi-Fi Gateway next to the
B.
existing Wi-Fi Gateway
· Disconnect the green data cable from the
existing Wi-Fi Gateway and connect it to
the new Wi-Fi Gateway
Green Data Port
Frame 6
Electrical
outlet
LINK
HD
RECORD
Existing Wi-Fi Gateway
TO TV
Pb
Y
Video
(VIDEO OUT)
NETWORK
D.
· Plug your new power cord into the Power port
Pr
S-Video
of the new Wi-Fi Gateway
· Plug the other end of the power cord into an
electrical outlet
Reset
POWER
New Wi-Fi Gateway
2.
Power up
LINK
Approximate time: 1–5 minutes
A.
Your Wi-Fi Gateway is now powering up. During this time, the Broadband light will turn
red and the Power light will turn solid green.
TO TV
(VIDEO OUT)
NETWORK
Wait up to 5 minutes for the Service indicator light to turn solid green.
During this time (up to 5 minutes), do not unplug the power cord or the green
data cable, as this can permanently damage the Wi-Fi Gateway and significantly
delay your service activation.
If the Service light does not turn solid green or continues to blink after 5 minutes,
Need more help?
see
B.
For U-verse TV, restart your TV receivers after the Service light is solid green.
Go to each TV and hold down the Power button on the U-verse receiver and DVR
for 10 seconds.
NOTE: Live TV may take a few minutes to display. If TV does not respond, refer
to
Need more help?
Reset
3.
Go Wi-Fi
POWER
MENU
OK
MENU
OK
LINK
HD
RECORD
USB
New Wi-Fi Gateway
Approximate time: 1–5 minutes
New Wi-Fi setup:
A.
TO TV
Select only one option to begin the Wi-Fi Setup
Audio
Pb
Y
Video
Audio
(VIDEO OUT)
NETWORK
Pr
S-Video
Option 1: Connect using PC
Optical
HDMI
USB
Optical
HDMI
· Connect laptop or PC with an Ethernet cable
to your Wi-Fi Gateway
B
· Continue to
B.
· Open a browser and go to ufix.att.com/restore
· Log in to your U-verse account. If you forgot your User ID (primary AT&T email address) and Password,
help can be found on the account log-in screen.
· Follow the onscreen instructions to transfer the existing Wi-Fi settings.
· Record existing Network Name and Wi-Fi Password on separate yellow sticker from kit.
· Place new yellow sticker over your new Wi-Fi Gateway's yellow sticker.
NOTE: If Wi-Fi settings did not transfer or to use new Wi-Fi Network Name and Password,
refer to the
NOTE: Any custom settings made for security cameras, game consoles, etc.,
on your original Wi-Fi Gateway will also need to be made on your new Wi-Fi Gateway.
Electrical
outlet
OK
HD
RECORD
MENU
USB
Video
Audio
Pb
Y
Pr
S-Video
Optical
HDMI
USB
on the back of this guide.
on the back of this guide.
USB
USB
Option 2: Connect using smartphone/tablet
· Establish a temporary connection using new Wi-Fi
settings located on yellow sticker on new Wi-Fi Gateway
· Open your device's Wi-Fi connection settings and
select your Wi-Fi Network Name and enter your Wi-Fi
Password to connect to your network
· Continue to
Need more help?
section on the back page of this guide.
POWER
ETHERNET
WIRELESS
HOME PNA
PHONE 1
PHONE 2
BROADBAND
SERVICE
New Wi-Fi Gateway indicator lights on
front panel. Lights may vary with setup.
B
USB
Reset
Advertisement
