GE JD630SF Dimensions And Installation Information

JD630SF
GE Appliances 30" Drop-In Electric Range
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
JUNCTION BOX LOCATION: Electric drop-ins are not approved for
installation with a plug and receptacle. This range is supplied with a flexible
conduit and must be hard wired to a junction box. See shaded area in drawing for
location of junction box. Refer to installation instructions for more information.
IMPORTANT: 30" DROP-IN RANGES ARE DESIGNED TO HANG
FROM THE COUNTERTOP. IT DOES NOT REST ON THE FLOOR.
FOR INSTALLATION ALTERNATIVES, REFER TO INSTALLATION
INSTRUCTIONS.
NOTE: This appliance has been approved for 0" spacing to adjacent
surfaces above the cooktop. However, a 6" minimum spacing to surfaces less
than 15" above the cooktop and adjacent cabinet is recommended to reduce
exposure to steam, grease splatter and heat.
OPTIONAL KITS FOR DROP-IN ELECTRIC RANGES: (Available At
Additional Cost)
REAR FILLER STRIP:
WB07T10680 – Black Filler Strip Assembly
INSTALLATION INFORMATION: Before
installing, consult installation instructions
for current dimensional data and additional
requirements.
NOTE: Check local codes for required
†
breaker size.
For answers to your Monogram, GE Café
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center
If necessary,
build up sides
to 1-1/4" thick
to provide
countertop
support
If you are NOT using the Filler strip:
23-3/16"
30"
If you are using the Filler strip:
If you are NOT using the Filler strip:
25"
30"
KW RATING
240V 11.9
208V 8.9
BREAKER SIZE
240V 40 Amps
†
208V 40 Amps
†
™ Series, GE Profile
® Service, 800.626.2000.
23-3/16"
DROP-IN ELECTRIC RANGE
DROP-IN ELECTRIC RANGE
DROP-IN ELECTRIC RANGE
Recommended
6" Min.
Recommended
from walls
27-1/2"
30"
If necessary,
build up sides
to 1-1/4" thick If necessary,
to provide build up sides
countertop
to 1-1/4" thick
27-1/2"
If necessary,
support
to provide
build up sides
countertop
to 1-1/4" thick
support
to provide
countertop
support
If you are NOT using the Filler strip:
24"
Above illustration intended for dimensional reference only.
2-7/8"
If you are NOT using the Filler strip:
23-3/16"
Refer to photograph for actual product appearance.
To Front Surface
of Countertop
30"
23-3/16"
2-7/8"
23-3/16"
To Front Surface
30"
of Countertop
20-5/8" Door
If you are using the Filler strip:
Clearance
From Front
30"
Surface of
25"
Countertop
If you are using the Filler strip:
30"
25"
If you are using the Filler strip:
30"
25"
Dimension and installation information are shown in inches.
30"
ADA
COMPLIANT
™ Series or
Acceptable Electrical Outlet
Area Also In Adjacent
15" Min.
Cabinet Or Under Floor
Conduit is 40" long
25"
Recommended
6" Min.
30" Min. 30" Min.
from walls
6" Min.
28-1/2"
30" Min.
from walls
30" Min.
30" Min.
Acceptable Electrical Outlet
23-3/16"
Area Also In Adjacent
Acceptable Electrical Outlet
30" Min.
Cabinet Or Under Floor
23-3/16"
Area Also In Adjacent
Conduit is 40" long
Cabinet Or Under Floor
Acceptable Electrical Outlet
23-3/16"
Area Also In Adjacent
Cabinet Or Under Floor
25"
27-1/2"
27-1/2"
30"
30"
31-1/4"
30"
24"
31-1/4"
27"
24"
2-7/8"
To Front Surface
of Countertop
24"
20-5/8" Door
Clearance
From Front
2-7/8"
Surface of
25-3/4"*
To Front Surface
Countertop
(excluding handle)
of Countertop
*Total depth from wall to
front of closed oven door 25-3/4"*
20-5/8" Door
(excluding handle)
Clearance
including handle is 28-1/2"
From Front
Surface of
Countertop
20-5/8" Door
Clearance
From Front
Surface of
Countertop
All GE ranges are equipped with
an Anti-Tip device. The installation
of this device is an important,
required step in the installation
of the range.
15" Min.
15" Min.
Conduit is 40" long
15" Min.
Conduit is 40" long
25"
28-1/2"
28-1/2"
25"
28-1/2"
31-1/4"
27"
31-1/4"
27"
*Total depth from wall to
front of closed oven door 27"
including handle is 28-1/2"
25-3/4"*
(excluding handle)
*Total depth from
front of closed
Listed by
including hand
Underwriters
Laboratories
25-3/4"*
(excluding handle)
*Total depth from
front of closed
including hand
Specification Revised 4/18