Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for FibroLAN MSM100U
Summary of Contents for FibroLAN MSM100U
- Page 1 MSM100U/ Module Universal Multi/Single-Mode To Single-Mode Media Converter User and Installation Guide Version: 2.0 FibroLAN Ltd. 6 Hayezira St. P.O. Box 544 Yokneam-Illit, 20692 ISRAEL Tel: 972-4-9591717 Fax: 972-4-9591718 E-mail: support@fibrolan.com Web site: www.fibrolan.com...
-
Page 2: Table Of Contents
If you still need help installing or troubleshooting the MSM100U/622U converter after reading the detailed information in this guide, please visit our web site (www.fibrolan.com), contact your reseller, or call FibroLAN directly. - Page 3 MSM100U Module Converter/Extender FEDERAL COMMUNICATIONS COMMISSION CANADIAN DEPARTMENT OF COMMUNICATIONS RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates, uses, and can radiate radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication.
-
Page 4: Overview
• DIP slide switches set-up 3 - Planning your network with MSM100U module When planning an optical network based on the MSM100U you have to take care of only one issue: the proper duplex mode of the entire network. As a rule, the entire network should be set to the same mode: FDX: in this case both throughputs and distances are maximized. -
Page 5: Module Models
MSM100U Module Converter/Extender 4 - Module models The MSM100U/622U modules are offered in the pre-configured versions as described in the table below: MSM100U-SMR7 Universal (100FX/ATM/OC3) Conversion Module, Multi Mode to Single Mode 1310nm, 7km 2*dual SC MSM100U-SMR Universal (100FX/ATM/OC3) Conversion Module, Multi Mode to Single... -
Page 6: Metrostar Chassis Layout
MSM100U Module Converter/Extender 5 - MetroStar chassis layout In slot position # 3 (from the left), it is possible to install an additional redundant Power Supply or the Blank panel BP-02. Metro Star™ Slot position # 4 is normally dedicated for the SNMP management Metro Star™... -
Page 7: Module Front Panel
MSM100U Module Converter/Extender 6 - Module front panel components Port 1 • Multi-Mode (or Single Mode) Duplex SC connector (Tx and Rx) • SD (Signal Detect) green LED – when lit indicates presence of Signal received on Rx side of the MM/SM DSC connector. -
Page 8: Installation Procedure
7 - Installation Slot assignment MSM100U module may be installed in any of the slots marked 1 to 12, However by installing modules systematically next to each other (from left to right) it will make it easier to install additional modules in the future allowing clear access to the slots. -
Page 9: F/O Cabling Connection
MSM100U Module Converter/Extender 8 - Fiber Optic Connection The MSM100U module is equipped with a pairs of Duplex SC-type connectors. Do not remove the protective covers on the fiber connectors until you are ready to connect the fiber optic cables. Power should be connected before attaching the fiber optic cables. -
Page 10: F/O Ports Specifications
Insert the single-mode F/O jumper (leading to the remote device or remote MSM100U) to the duplex SC connector located on the bottom side of the module front panel (port 2). Make sure that the fiber leading from the transmit connector of that device connects to the RX port and vice versa and that the connectors of both ends of jumper are tightly inserted. -
Page 11: Dip Slide Switches Setting
MSM100U Module Converter/Extender 10 - DIP slide switches setting Each MSM100U/622U module contains on its motherboard an array of 4 DIP Slide switches, the tasks of which are shown in the following drawing. DIP slide switches DIP slide switches default setting... -
Page 12: Typical Network
MSM100U Module Converter/Extender 12 - Typical Network The Central Node and the remote sites are interconnected by means of MSM100U media converter modules installed in the FibroLAN MetroStar System and by the remote FibroLAN U.CON1 converter devices. These units are also stand-alone Universal Multi-mode to Single Mode Media Converters (range: 25/40/70/100/150Km), supporting Fast Ethernet and ATM/OC3. -
Page 13: Troubleshooting
If the problem persists after carrying out the above procedure, do the following: exchange your MSM100U or MSM622U with another similar module believed to be functional, and re-perform the requested check. If that has solved the problem, send the faulty module for repair. If the problem still persists, there is probably some sort of general network failure. -
Page 14: Specifications
14 - Specifications Standard Compliance: ATM-OC3, 100Base-FX Conversion Method: Protocol Transparent Fiber Optic ports specifications Refer to the F/O port specifications in section 9 for all MSM100U modules Diagnostics: Power LED SD LED: Signal Detect for MM/SM Rx port 1... -
Page 15: Warranty Limitation
You must claim repairs or replacements under this warranty only from the reseller from which you have purchased the device, however you may refer directly to FibroLAN Ltd. to claim the warranty providing reasonable proof that the reseller ceased operation and/or unreasonably refused to provide you with the service.