Advertisement
IN-LINE THERMOSTATIC SHOWER VALVE
11
Ø57
43
85
143
BEFORE CONNECTION FLUSH WATER THROUGH PIPEWORK TO REMOVE
ALL GRIT & DEBRIS WHICH COULD DAMAGE THE VALVE MECHANISM
INSTALLER:
After installation please pass this instruction booklet to the user
Installation Instructions
45º
41
Ø69
Ø33
G½
150
40º
Ø52
182
A5322AA In-line Thermostatic Shower Valve
A5525AA Second Outlet Kit
A5526AA Retro Fit Installation Kit
30
Ø31.5
115.5
15mm
compression
Ø21
Ø26
Advertisement
Table of Contents
Related Manuals for Ideal-Standard A5322AA
Summary of Contents for Ideal-Standard A5322AA
- Page 1 15mm compression Ø21 Ø26 40º Ø52 A5322AA In-line Thermostatic Shower Valve A5525AA Second Outlet Kit A5526AA Retro Fit Installation Kit BEFORE CONNECTION FLUSH WATER THROUGH PIPEWORK TO REMOVE ALL GRIT & DEBRIS WHICH COULD DAMAGE THE VALVE MECHANISM INSTALLER: After installation please pass this instruction booklet to the user...
- Page 2 The fittings covered by these instructions should be installed in accordance with the Water Regulations published in 1999*. Ideal Standard strongly recommends that these fittings are installed by a professional fitter. *A guide to the Water Supply (Water Fittings) Regulations 1999 and the Water Byelaws 2000, Scotland is published by WRAS (Water Regulations Advisory Scheme) Fern Close, Pen-y-Fan Industrial Estate, Oakdale, Newport, NP11 3EH.
-
Page 3: Supply Conditions
- 3 - SUPPLY CONDITIONS Table 1 Conditions for normal use BSEN1111 BSEN1287 Operating pressure range: High Pressure Low Pressure Maximum static pressure - Bar Flow pressure hot and cold - Bar 0.5 to 5.0 0.1 to 1.0 Hot supply temperature - °C 55 to 65 55 to 65 Cold supply temperature - °C... -
Page 4: Water Regulations
- 4 - WATER REGULATIONS CATEGORIES OF RISK The water regulations published in 1999* take a new approach to backflow in that they look at different categories of risk. The installer must assess the risk from the various categories of fluid in adjacent appliances before determining the level of backflow protection required for a particular installation. - Page 5 - 5 - INSTALLATION GUIDE The thermostatic mixing valve must be installed in such a position that maintenance of the TMV and its valves and the commissioning and testing of the TMV can be undertaken. 1. The Thermostatic mixer can be installed with rear, rising or falling supply inlets. Decide on the most appropriate method of your installation, and rotate the elbows to suit.
- Page 6 - 6 - INSTALLATION GUIDE continued 8. For rear entry supplies only: Fit the concealing plates over the inlet pipes. Note! Apply silicone sealant to the back face of the plate. cold Concealing plate Apply silicone sealant to back Figure 8 face of flange 9.
-
Page 7: Operation
- 7 - OPERATION colder hotter temperature control handle flow control handle Figure 10... -
Page 8: Maintenance
Figure 11 CALIBRATION In the event of the thermostatic cartridge requiring re-calibration the following procedure should undertaken. 1. Remove the Ideal Standard logo button and disconnect the handle. 2. Slide out the red "U" piece (b) exposing temperature control mechanism (d). - Page 9 The purpose of servicing regularly is to monitor the performance of changes in system and valve set up. This may require the need to adjust either the supply system or the valve. The A5322AA should be checked and tested 12 months after commissioning.
- Page 10 - 10 - THERMOSTATIC CARTRIDGE REPLACEMENT 1. Remove the temperature control handle by first prizing out the index button with a small screwdriver and then removing the “pozi-drive” screw Figure 13 2. Remove the temperature handle carrier. To do this slide the black serrated lever in a clockwise direction with a screwdriver.
- Page 11 - 11 - MOVING THE OUTLET MECHANISM TO THE TOP OF THE FITTING (For fixed head exposed riser) Important! Mixer must not be connected to the water supply when moving the outlet mechanism. 1. Using a small screwdriver carefully remove the plug cap from the sealing plug at the top of the mixer. 2.
- Page 12 - 12 - INSTALLING THE OPTIONAL SECOND OUTLET A5525AA (NOT SUPPLIED) plug cap The second outlet kit allows your thermostatic mixer to sealing plug be connected to a fixed overhead shower Kit contains 2.5mm A/F Hexagonal Key, ILV Assembly Clockwise Close, Instruction leaflet Important! Mixer must not be connected to the water supply when...
- Page 13 - 13 - RETRO FIT INSTALLATION WITH ADJUSTABLE INLETS PACK - A5526AA (NOT SUPPLIED) The adjustable inlets each have adjustment of 4mm, allowing your thermostatic mixer to be connected to pipe centres ranging from 147mm to 155mm The adjustable external backplate allows for 5mm adjustment from the finished wall surface Kit contains: Adjustable Inlet Elbows x 2 External Backplate...
- Page 14 - 14 - 10. Tighten the compression nuts onto the mixer with a suitable spanner. Figure 20 Caution! Take care not to damage the chrome surfaces. 11. Tighten the adjustable backplate grubscrews with a 2.5mm hexagonal key (supplied) to secure the mixer to the backplate.
-
Page 15: Spare Parts
- 15 - SPARE PARTS... - Page 16 A962624AA Flow restrictor 4 l/min A962570NU Flow restrictor 8 l/min A962571NU Ideal Standard pursues a policy of continuing improvement in design and performance of its CUSTOMER CARE HELP LINE products. 0870 129 6085 The right is therefore reserved to vary specification without notice.
Need help?
Do you have a question about the A5322AA and is the answer not in the manual?
Questions and answers