Kohler SYMBOL 72641T Installation Instructions

温度测试与调整
在温度测试前，应确保供水系统充分
且有较高的温度。温控把手在37度位
置时，打开龙头让水流出。进行温度
测量，出厂时温度设定在36~38度范围
内。如超出这个范围，要进行调整。
调整的步骤如下：
Spindle
阀轴
取下把手上盖，用螺丝刀取下螺钉和
温控把手组件。在正常水流状态下，
由冷水位置开始慢慢转动温控阀轴(保
持同一方向)直至获得37度的水流。如
果温度超过38度，回到冷水位置重新
调整。
温度稳定后，不要转动温控阀轴，安
装温控把手，使温控把手的参考标识
与数字37对齐。锁紧螺钉，安装把手
上盖(图Fig.5)。
维护与保养
滤网垫片(18)可起到保护龙头的作用，
但长时间使用后水垢或杂质可能会堵
塞滤网降低水流量。如有类似情况发
生，卸下龙头，用六角扳手(12mm)将
底座(20,顺时针)拧下，取下螺母(19)、
滤网垫片(18)和单向阀(17)。用热醋清
洗滤网。然后按照图示装回。(注意：
单向阀必须按原方向装回) 。
如果供水的水质较硬或长时间使用，
水垢或杂质会阻塞温控阀上的滤网，
流量会降低。需要清理请按照下列步
骤进行：关闭供水系统，使流量阀处
于打开位置后进行温控阀拆卸作业。
Fig.7
温控阀是较敏感的配件，所以要十分
小心。
拆卸前确保指示标识与数字37对齐。
拆卸把手组件(Fig.7),然后将螺母和塑 Cartridge
温控阀
料套卸下(Fig.8)。小心地卸下温控阀
(Fig.9)。用热醋进行清洗。清洗后，将
Fig.9
塑料套和螺母(限位组件)装到温控阀上
Notch
面，使塑料套的定位柱嵌入温控阀的
限位槽
Stop pin
限位槽内(Fig.10)。然后将塑料套的定
定位柱
位柱与龙头本体内孔凹槽对齐，装入
温控阀并锁紧螺母(Fig.11)。
Cartridge and stop assembly
阀体限位组件
Fig.11
837392-D
Verification and Setting
Make sure that the water feeds of the
Number 37
数字37 faucet have reached their highest
temperature by letting the water run
Reference mark
参考标识
sufficiently. With the selector in position
37ºC, the temperature of the water
coming out of the faucet must be within a
range of 36ºC and 38ºC, as measured by
a bath thermometer. If this is not the
case, the installer can adjust the setting.
Proceed with the setting as follows:
Uninstall handle kit. With the faucet on
Fig.5
'cold' normal water flow, slowly turn the
temperature selector(always in the same
direction) until water at 37ºC is obtained.
If the temperature goes over 38ºC, go
back to the 'cold' setting and set again.
When the temperature is stabilized,
without turning the cartridge spindle,
make sure the reference mark of the
temperature handle aligned with the
number37. Tighten the screw,put on the
handle plug. See fig.5.
CARE AND MAINTENANCE
The filters(18) protecting the faucet
device may get obstructed and reduce
water flow. When this happens, unscrew
18
the bushes(20, left thread) by a
19
wrench(12mm) and take out the nuts(19),
filters(18) and the check valves(17) after
17
removing the faucet. Clean the filters by
soaking them in warm vinegar. Reinstall
20
them as the figure.(Note: Check valves
Fig.6
should reinstall as original orientation).
Very hard water can obstruct the filters
protecting the thermostatic cartridge and
reduce the flow of water. Please clean
the cartridge as follows: Shut off the
water supply of the faucet and open the
Fig.8
water flow handle, then proceed to
Stop assembly
remove the cartridge. The cartridge is
限位组件
sensable, please be careful.
Stop pin
Fig.2 Make sure the reference mark is aligned
定位柱
with number 37 before your action.
Notch
限位槽
Remove the handle kit(Fig.7), unscrew
Cartridge
the nut and stopper(Fig.8). Removing the
Fig.10
温控阀
cartridge cautiously(Fig.9). Clean the
Round mark
thermostatic cartridge by soaking it in
圆孔标识
Groove warm vinegar. After cleaning, install the
凹槽
'stop assembly' back on the cartridge,
adjusting the stop pin into the notch
(Fig.10). Install the assembly cartridge
and stop in the body, adjusting the stop
pin into the notch(Fig.11).
Fig.12

INSTALLATION INSTRUCTIONS

安装说明书
安装之前
所有的资料是按最新出版的产品资料编写而成。科
勒公司保留任何时候不经通知即可改变产品特性、
包装或产品可供类型的权利
说明书包括重要的安装、保养及清洁方面的内容，
请把这些资料交给用户阅读。
使用环境
1.最小供水压力：0.5bar(0.05MPa)。
2.推荐冷热供水的静态压力：3bar(0.3MPa)。
3.如果供水压力大于5bar(0.5MPa)，安装减压阀。
4.热供水温度最低：50°C；最高：80°C。
5.推荐的热供水温度：65°C。
6.温度的设定基本范围为：20°C到50°C。
7.安全限位温度：40°C。
8.冷热供水压力差不大于2bar(0.2MPa)。
9.花洒最高使用环境温度：60°C。请特别注意花洒
同花洒连接的臂管必须远离加热器，否则可能损坏
花洒及其密封件，甚至对使用者造成伤害。
安装尺寸
G1/2˝
97~102
205
20 Max.
72641T
4 837392-D
Wall-Mount Thermostatic
72641T
挂墙式恒温浴缸花洒龙头
72643T
挂墙式恒温花洒龙头
BEFORE YOU BEGIN
All information is based on the latest product
information available at the time of publication.
Kohler Co. reserves the right to make changes in
。
product characteristics, packaging, or availability at
any time without notice.
Please leave these instructions for the consumer.
They contain important information.
OPERATION CONDITION
1. Minimum supply pressures: 0.5bar(0.05MPa).
2. Recommended supply static pressures:
3bar(0.3MPa) on hot and cold water.
3. Supply pressure greater than 5bar(0.5MPa) : install
a pressure reducer.
4. Hot water temperatures, minimum: 50°C,
maximum:80°C.
5. Recommended hot water temperature: 65°C
(energy-saving).
6. Setting range, approximately: 20°C to 50°C.
7. Safety stop at: 40°C.
8. Pressure difference between hot and cold supply:
2bar(0.2MPa) maximun..
9. The highest environment temperature for handspray
& showerhead is 60°C. Please keep handspray,
showerhead and the shower arm away from heater, or
it may become damaged and cause injury to the user.
ROUGH-IN DIMENSIONS
49
60
Ø122
G1/2˝
Ø59
G1/2˝
G1/2˝
G1/2˝
星珀
YMBOL
20 Max.
72643T
1