Download Print this page
Labgear LMA209F Installation Instructions

Labgear LMA209F Installation Instructions

9db/13db gain 1/2 way masthead amplifier 4g with lte800 filters ready

Advertisement

Quick Links

Installation Instructions

General Safety Precautions
• If you are in any doubt about an installation, refer to a qualified aerial installer.
• When working on an installation outside, beware of overhead power lines.
• Observe safe working practices, tread carefully and ensure adequate lighting is available
in loft or roof space.
• Always follow manufacturer's operating/safety instructions when using tools/ equipment.
• Only carry out work outdoors at height if you are competent in the use of ladders and related
access equipment.
• Always read and follow the manufacturer's instruction label affixed to the ladder.
2 –Year Guarantee
Your amplifier is guaranteed against faulty components or poor workmanship for a
period of two years from the date of purchase.
This guarantee does not cover accidental or malicious damage (Including damage from
natural causes such as lightening) and will be invalidated by installation or use other
than in accordance with these instructions, repair or attempted repair other than by the
manufacturer, or open or removal of the case. This does affect your statutory rights.
Labgear Reserve the right to modify their designs or specifications, In the light of future
developments, without prior notice. Performance figures quoted are typical and subject
to normal manufacturing and service tolerances
For further information or any queries please contact
Customer Careline: 08457 573 479
(Local rate – UK only)
Technical Support: www.philex.com/support
4
Waste electrical products should not
be disposed of with household waste.
Please recycle where facilities exist.
Check with your Local Authority for
recycling advice.
© Philex Electronic Ltd. 2013 V1.1
LMA113F 13dB Gain 1 Way Masthead Amplifier
LMA209F 9dB Gain 2 Way Masthead Amplifier
(with Lte800 filters)
Installation Instructions
Introduction
These technically advanced UHF antenna pre-
amplifiers offer an unparalleled combination of low
noise, good input filtering and medium output.
The amplifier units consist of fully screened modules
fitted with f connectors. They are enclosed in a
moulded ABS weatherproofing housing suitable for
outdoor applications.
They both have an integrated sturdy metal mast clamp
so that they can be quickly and securely fitted to masts.
The amplifiers also tilt by 45˚ to make the
attachment of f plugs to the sockets much easier.
The built in filter removes signals above 790MHz
emitted by Lte 800 4G phone transmitters and
picked up by the attached aerial.
Other features include
• Industry-leading noise performance
• Sturdy metal mast clamp
• LED power indicator, a useful aid to fault finding
• Inputs well filtered below 470MHz to minimise interference from Tetra transmissions
• The amplifier is suitable for Indoor or outdoor use
• The LMA209F can be powered via either of its outputs
Power Supply
Both units require an independent 12VDC 30-35mA
power supply we recommend the use of the PSUF
12V, 100mA power supply unit with short circuit
protection and a fault indication LED which changes
from Green to Red. If using as a pre-amplifier with the
LDA204L, LDA2061L or LDA2081L you do not need an
additional power supply, these distribution amps have
built-in line powering.
LMA113F
This 13dB model improves signal strength and C/N
in domestic and MATV systems with normal length
downlead cables.
This is ideal for use in digital installations where they
will enable the minimum recommended signal level
(45dBμV) to be delivered to the tuner and reduce the
likelihood of impulse interference problems.
LMA209F
This amplifier with 9dB gain per port is ideal for feed-
ing two TV points from one antenna.
The downleads can be run mainly on the outside of
the building, making this a popular solution for retro-
fit on older buildings.
It can be powered from either output, allowing flexi-
bility in the power unit location.
Lte
800
READY
LMA113F Connection
Power
pass
OUT 1
IN
Power
LED
PSUF
PSW111
TV outlet
LMA209F Connection
Power
pass
Power
pass
IN
OUT 1
OUT 2
PSW111
TV outlet
Power
LED
PSUF
PSW111
TV outlet
1

Advertisement

loading

Summary of Contents for Labgear LMA209F

  • Page 1: Installation Instructions

    This is ideal for use in digital installations where they will enable the minimum recommended signal level Power (45dBμV) to be delivered to the tuner and reduce the Labgear Reserve the right to modify their designs or specifications, In the light of future pass Power pass likelihood of impulse interference problems.
  • Page 2 Signal connections are made to the coaxial sockets on the right-hand side of the power unit. Good quality coaxial cable to EN50117-2 must be used. Labgear recommend the use of CAI “benched marked” cable. • The down lead from the masthead amplifier must be connected to the socket marked ‘IN’ .

This manual is also suitable for:

Lma113f