Advertisement
The Sensor snaps into the tabs at the top.
Confirm that the sensor is properly positioned to detect
motion and has sufficient light to operate – refer to the "Walk
Test" and the "Light Test" sections
Linking:
Two or more compatible devices can be linked and configured
to provide the desired control. There are two basic types of
devices in the system; transmitters and transceivers.
Transmit Only: Transmitters are simple energy harvesting
devices that send RF messages to communicate a condition
level or state. Transmitters can only be linked to transceivers.
Examples: Rocker Switches, Occupancy Sensors
Transmit and Receive: Transceivers are controlling devices that
send as well as receive RF messages. They also process
relevant control logic and actuate the appropriate outputs
(switching a light on or off for example). Transceivers can be
linked with transmitters as well as other transceivers.
The Occupancy Sensor is a Transmit-only Device:
To link the occupancy sensor to a transceiver, the transceiver
must first be powered, within wireless range of the sensor, and
set to accept links. The TILT WLVD is a transceiver.
Next, the desired transmitter, is triggered to send a special link
message. The awaiting transceiver receives and stores the link
permanently so the devices can interact to provide a variety of
intelligent options.
To Link or Unlink an Occupancy Sensor:
1. Set the TILT WLVD of other transceiver
to the desired Link/Unlink mode.
2. Click the Menu button on the bottom
of the sensor once. This sends a
link/unlink radio signal to the WLVD.
NOTE: The button interface on the sensor is used for linking
and testing only. The occupancy timer settings are configured
on the WLVD or other transceiver to which the sensor is linked.
Refer to the "Linking" section of the installation guide for the
WLVD or other transceiver to complete the linking and setup
process.
© Lauren Illumination, 2015
Occupancy Sensor – Wall Mounted Installation Guide
Testing the Sensor:
Before starting a test, ensure that the sensor's energy storage is fully
charged by placing it under a bright light (at least 500lux) for 20
minutes, or insert a battery for 5 minutes while in a well-lit area.
NOTE: If the sensor does not have a sufficient charge, it cannot enter
into the test mode. No LED light or 1 red blink when the set button
is pressed indicates insufficient charge.
If a battery is used to charge the sensor for a light test, ensure it is
removed to get an accurate light measurement.
A test mode will stay active for 3 minutes. To exit a test and resume
normal operation, press and hold the Menu button for 5 seconds.
Walk Test:
Use the walk test to confirm that motion is within the sensor's
range.
1. Press and hold the Set button for 5 seconds. RED LED will blink.
2. Move in and out of the sensor's range to determine its coverage
area. Sensor will blink.
3. Make small hand movements just inside the limit of the sensor's
range to see if the motion triggers a response
NOTE: Ensure that the sensor does not falsely trigger from user
activity outside of the desired zone or other heat and motion
sources. If false triggering occurs, adjust the sensitivity switch from
REG to LOW
Light Test:
Use the light test to measure real-time light levels and confirm
whether the occupancy sensor has sufficient light.
1. Create a realistic lighting condition (the test measures the real-
time light level).
2. Press and hold the Set button for 10 seconds. RED and GREEN
LEDs will blink.
3. Watch the LED blink rate to determine the light strength. The
highest rate is 5 blinks which indicates very good light (>200lux).
1 blink indicates the minimum light level (<25 lux)
NOTE: If there is no blink rate, consider relocating the sensor or
installing a battery to provide supplemental power.
Optional Settings:
Two additional settings can be configures via button presses which
may be useful in some installations. Note that these settings
consume additional energy and are not advisable for low-light
operation:
Page 3
Advertisement
