Page 2
Barco nv Home Cinema Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.84.30 Fax: +32 56.36.88.62 E-mail: salesassistantht.bci@barco.com Visit us at the web: www.homecinema.barco.com Printed in Belgium...
Page 3
Changes Barco provides this manual “as is” without warranty of any kind, either expressed or implied, including but not limited to the implied war- ranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time without notice.
Installation Instructions Before operating this equipment please read this manual thoroughly, and retain it for future reference. Installation and preliminary adjustments should be performed by qualified BARCO personnel or by authorized BARCO service dealers. Owner’s Record The part number and serial number are located at the back side of the projector. Record these numbers in the spaces provided below.
For this reason, it is absolutely necessary to leave an "exclusion zone" around all external surfaces of the projector whereby no flammable or combustible materials are present. The exclusion zone must be not less that 10 cm (4") for Barco Retro Projectors.
Page 11
If the product exhibits a distinct change in performance, indicating a need for service. • Replacement parts: When replacement parts are required, be sure the service technician has used original BARCO replace- ment parts or authorized replacement parts which have the same characteristics as the BARCO original part. Unauthorized substitutions may result in degraded performance and reliability, fire, electric shock or other hazards.
The power input voltage is autoranging between 100V (-10%) and 240V (+6%). 2.3 Switching ON/OFF Switching and led indication The projector is switched ON and OFF using the power (mains) switch ON/OFF. • Pressed : ON • Not pressed : OFF R5976584 BARCO CINE7 26022003 2. AC Power...
Page 14
The projector can start now in the ’operational mode’ (image displayed) or in the ’stand by mode’, depending on the software setup. Stand by indication lamp : • no light up : projector in operational mode • red : projector is in stand by. Leds on the front plate of the projector Image 2-2 R5976584 BARCO CINE7 26022003...
4. Input signal : R-Y, Y and B-Y with separate sync or with compositesync. 5. Input signal : R-Y, Y and B-Y with separate tri level sync or with composite tri level sync. R5976584 BARCO CINE7 26022003 (B-Y) [Component Input] 3.
Video input selection via the keypad 1. press ADJUST key. The General access menu is displayed on the screen. (image 3-3) 2. Use the cursor keys to highlight 1. 3. Press ENTER to select the highlighted source. Image 3-3 R5976584 BARCO CINE7 26022003...
Video input selection via the keypad 1. press ADJUST key. The General access menu is displayed on the screen. (image 3-5) 2. Use the cursor keys to highlight 2. 3. Press ENTER to select the highlighted source. R5976584 BARCO CINE7 26022003 3. Source Connections...
Page 18
8. Press ENTER to display the Random Access menu. (menu 3-5) 9. Select Picture Tuning. 10.Press ENTER to display the picture tuning menu. (menu 3-6) 11.Select Port2 : Video. 12.Press ENTER to toggle between VIDEO or S-VIDEO. 13.Press ADJUST to return to operational mode. R5976584 BARCO CINE7 26022003...
Connect your RGB source with sync on green, composite or separate sync via an interface to RGBS input. Always use an interface (e.g. Barco Magik Interface R9828120) when a computer and local monitor have to be connected to the projector as the signal cable coming from the computer is limited to 60 cm due to interferences.
RGB3S or RG3sB selection via the local keypad 1. Press ADJUST key to start up the adjustment mode. The General Access menu will be displayed. (image 3-9) 2. Use the cursor keys to highlight 4 3. Press ENTER to select the highlighted source. R5976584 BARCO CINE7 26022003...
Always use an interface (e.g. Barco Magik Interface R9828120) when a computer and local monitor have to be connected to the projector as the signal cable coming from the computer is limited to 60 cm due to interfer- ences.
Component input selection via the local keypad 1. Press ADJUST key to start up the adjustment mode. The General Access menu will be displayed. (image 3-13) 2. Use the cursor keys to highlight 6 3. Press ENTER to select the highlighted source. R5976584 BARCO CINE7 26022003...
Sending data to the projector or copying the data from the projector to a hard memory device. Image 3-14 RS232 connection How to set up the baud rate for the communication with a computer? See changing the baud rate in the chapter Service Mode of the Owner’s Manual. R5976584 BARCO CINE7 26022003 3. Source Connections...
12 V output voltage to trigger external equipment such as screen up/down, curtains open/close etc. This voltage is available when the projector switches from standby to operational mode. When the projector returns into standby mode, the 12V trigger voltage disappears too. Image 3-15 R5976584 BARCO CINE7 26022003...
4. Lift up the battery at the same time. 5. Repeat for the second battery. 6. Insert the batteries as indicated in the RCU (battery type AA or LR6 or equivalent). 7. Put the battery cover on its place. (image 4-1) R5976584 BARCO CINE7 26022003 4. Getting Started...
The common address can be zero (0) or one (1). The standard RCU are setup for common address zero. To change the common address of the RCU, contact a BARCO service center. If it is necessary to program the projector address into the RCU, see chapter ’Getting Started’.
Address key Selection key (*) PAUSE R5976584 BARCO CINE7 26022003 user programmable keys with functions for direct access. Adjust key, to enter the adjustment mode (recessed key), to enter the address of the projector (between 0 and 9). Press the recessed address key with a pencil, followed by pressing one digit button between 0 and 9.
Page 28
(This is a visual indicator to check the operation of the remote control) R5976584 BARCO CINE7 26022003...
The projector starts up in stand by. Press a digit key corresponding to the desired source or press STBY key. The projector displays the selected source or the warm up cycle message. When this warm up message appears on the screen, handle as described in ’Start up in Operational Mode’. R5976584 BARCO CINE7 26022003 Switched OFF Operational mode Stand By mode 4.
When using the wireless remote control, make sure you are within the effective operating distance (30m, 100ft in a straight line). The remote control unit will not function properly if strong light strikes the sensor window or if there are obstacles between the remote control unit and the projector’s IR sensor. R5976584 BARCO CINE7 26022003...
0 and 9). The projector with the corresponding address will listen to that specific RCU. Common Address Every projector has a common address ’0’ or ’1’. The choice between ’0’ and ’1’ can be selected in the Service mode. R5976584 BARCO CINE7 26022003 4. Getting Started...
+ or - side of the button of the control are pressed. Access via the local keypad 1. Press the ADJUST key to display the General access menu. 2. Use the cursor keys to highlight the desired analog control. 3. Press ENTER to select. R5976584 BARCO CINE7 26022003...
When the Pause key is pressed, the image projection is stopped, a blue or black screen will be displayed and the projector remains with full power for immediate restart. The sound is not interrupted. The display on front of the projector will show a "P". R5976584 BARCO CINE7 26022003 4. Getting Started...
Page 34
Press EXIT key • Select a source number. The Freeze key (Only with Line Multiplier) When the Freeze key is pressed, the image is frozen until this key is pressed again (only with built in Line Multiplier). R5976584 BARCO CINE7 26022003...
Function Keys - Gives an overview of the programmed function for each key. • Service Menus - Installation and adjustment menus to set up the projector. Before entering a warning will be displayed. R5976584 BARCO CINE7 26022003 5. Start up of the adjustment mode...
When the analog control is adjusted the projector returns automatically to the General access menu. When you want to return to the Adjustment mode, press EXIT, otherwise select quit ADJUST and press ENTER to return to operational mode. R5976584 BARCO CINE7 26022003...
Function keys • Service menus Iris Guided Random Access Installation Service 6.2 Image Control Overview • Starting up the image controls • Line Multiplier • Color Adjust, Color temperature set up • Format Select R5976584 BARCO CINE7 26022003 6. Main Menu...
Format Select Select with then <ENTER> <EXIT> to return Menu 6-2 IMAGE PROCESSING Line Multiplier : Multiplier Mode Motion Processing : Video Equalizing Noise Reduction Contrast Enhancement Select with then <ENTER> <EXIT> to return Menu 6-4 R5976584 BARCO CINE7 26022003...
The sharpness of the image can be adjusted for 3 frequency bands (low, medium and high) separately. In addition to the 7 prepro- grammed factory presets a customized adjustment of the sharpness for 3 ranges is also possible. Vertical frequency of the image Quantity of horizontal lines Interlace mode R5976584 BARCO CINE7 26022003...
Video Equalizing Noise Reduction Contrast Enhancement Select with then <ENTER> <EXIT> to return Menu 6-12 R5976584 BARCO CINE7 26022003 to adjust the sharpness in the chosen frequency band (Low, Mid or High) or to scroll through the 6. Main Menu...
The color temperature of the image can be installed. The customer has the choice between 4 factory preset color temperatures and one custom. This custom color temperature has to be adjusted in the Random Access Adjustment Mode. R5976584 BARCO CINE7 26022003...
Select with then <ENTER> <EXIT> to return Menu 6-16 6.2.4.2 Adding a name to a Format What can be done? A name can be added to an available format. R5976584 BARCO CINE7 26022003 COLOR ADJUST Broadcast 3200 Film 4900 Video 6500...
FORMAT LIST Source 01 Video Available xxxxxx Free xxxxxx Available BARCO Free xxxxxx Free xxxxxx Free xxxxxx Free xxxxxx Free xxxxxx Select with then <ENTER> <EXIT> to return <TEXT> to enter a name R5976584 BARCO CINE7 26022003 to select the...
The autoconvergence on the current source will be carried out automatically, starting from the existing settings. By projecting alter- nately red and blue lines, 25 convergence areas are aligned onto the green pattern. R5976584 BARCO CINE7 26022003 IRIS CONTROL IRIS Touch Up...
<ENTER> <EXIT> to return Menu 6-26 6.4 Sound Control What can be done? When the sound option is available, the following sound modes can be selected : normal stereo, spatial stereo, pseudo stereo or mono. R5976584 BARCO CINE7 26022003...
With the complete set of Service menus such as IRIS, Guided, Random Access, Installation and Service it is possible to adjust the projector completely. When entering the Service Menus, a warning will be displayed mentioning that only qualified service personnel may enter the Service menus. R5976584 BARCO CINE7 26022003 SOUND CONTROL Select sound mode : Normal Stereo...
Page 48
! If qualified, press <ENTER> to continue, or if not, <EXIT> to return. Menu 6-32 Menu 6-33 ADJUSTMENT MODE IRIS GUIDED RANDOM ACCESS INSTALLATION SERVICE Source 01 Select with then <ENTER> <EXIT> to return R5976584 BARCO CINE7 26022003...
3. Press ENTER to select. The Main menu will be displayed (menu 7-1). 4. Continue as described in How to enter the Adjustment menus with the RCU. R5976584 BARCO CINE7 26022003 WARNING RISK OF INCORRECT Select a path from below : ADJUSTMENT OF THE PROJECTOR.
Some items in the Service menus are password protected. While selecting such an item, the projector asks to enter your password. Password Protection is only available when the password strap on the controller module is on. Contact a Barco authorized technician when no password is requested during the adjustment procedure and Password Protection is desired.
Page 51
When reentering the adjustment mode, it will be necessary to enter your password again when selecting a password protected item. When the password is wrong, the error message “Wrong Password !!!” will be displayed. R5976584 BARCO CINE7 26022003 7. Entering the service menus...
Page 52
7. Entering the service menus R5976584 BARCO CINE7 26022003...
Some items in the Random access mode are password protected (when the password function is enabled). Enter your password to continue. All other password protected items are now also available if you stay in the adjustment mode. R5976584 BARCO CINE7 26022003 8. Random Access Adjustment Mode...
DECODING : EBU PORT2 : VIDEO PEAKING LINE MULTIPLIER : ON Select with then <ENTER> <EXIT> to return Menu 8-7 R5976584 BARCO CINE7 26022003 PICTURE TUNING COLOR BALANCE SYNC: FAST DECODING : EBU PORT2 : VIDEO PEAKING LINE MULTIPLIER : ON Select with then <ENTER>...
Select with arrow keys then <ENTER> adjust red with Blue with <EXIT> to return Menu 8-10 to select Red & Blue below Custom white Balance. (menu 8-10) to adjust the blue gain. to select Green below Custom white Balance. R5976584 BARCO CINE7 26022003...
8.5.4 Decoding What can be done? Only for NTSC signals. R5976584 BARCO CINE7 26022003 to select Red & Blue below Custom black Balance. (menu 8-11) to adjust the blue cut-off. to select Green below Custom black Balance. 8. Random Access Adjustment Mode...
<EXIT> to return Menu 8-14 8.5.6 Peaking What can be done? Peaking improves the contours in an projected image. The Peaking function is only available for RGBS, RGsB, component, tri level and component tri level sources. R5976584 BARCO CINE7 26022003...
RGB signals on 15 kHz. The setting of the line multiplier will be saved together with the source number. Each time this source number is selected, the last saved version will be loaded. R5976584 BARCO CINE7 26022003 PEAKING LOW FREQUENCY...
<EXIT> to return Menu 8-20 IMAGE PROCESSING LINE MULTIPLIER : ON MOTION PROCESSING: ON OUTPUT MODE VIDEO EQUALIZING NOISE REDUCTION CONTRAST ENHANCEMENT SPLIT SCREEN: OFF ADVANCED SETTINGS Select with then <ENTER> <EXIT> to return Menu 8-18 R5976584 BARCO CINE7 26022003...
CONTRAST ENHANCEMENT SPLIT SCREEN: OFF ADVANCED SETTINGS Select with then <ENTER> <EXIT> to return Menu 8-25 R5976584 BARCO CINE7 26022003 LINE MULTIPLIER OUTPUT MODE 50Hz 625 Lines NI 50Hz 935 Lines NI 100Hz 625 Lines NI 50Hz 1250 Lines NI...
SPLIT SCREEN: OFF ADVANCED SETTINGS Select with then <ENTER> <EXIT> to return Menu 8-26 Image 8-2 Dynamic Noise Reduction bar scale 8.5.7.7 Contrast Enhancement What can be done? Enhancing the contrast results in a more dynamic image. R5976584 BARCO CINE7 26022003...
TIME BASE CORRECTION LUMINANCE DELAY V SYNC REF: INDIRECT CLAMP GATING: OFF LIMO PLUS OPTIONS FACTORY PRESET WARNING: ADVANCED ADJUSTMENT SHOULD BE PERFORMED ONLY BY QUALIFIED PERSONNEL Select with then <ENTER> <EXIT> to return Menu 8-30 R5976584 BARCO CINE7 26022003...
Clamp Gating is useful when protection signals are present in the vertical interval of the video signal (macrovision), that would otherwise confuse the Limo Pro, causing horizontal brightness differences near the top of the screen. R5976584 BARCO CINE7 26022003 8. Random Access Adjustment Mode...
WARNING: ADVANCED ADJUSTMENT SHOULD BE PERFORMED ONLY BY QUALIFIED PERSONNEL Select with then <ENTER> <EXIT> to return Menu 8-35 8.5.7.10.7 Coring What can be done? With coring, a noise threshold will be set for all filters. Indirect R5976584 BARCO CINE7 26022003...
8.5.7.10.8 LTI Luminance transient improvement. What can be done? This function makes the luminance transients sharper (from dark areas to highlight areas) without overshoot, undershoot or ringing. Image 8-6 LTI basic principle R5976584 BARCO CINE7 26022003 8. Random Access Adjustment Mode...
Color transient improvement. To improve the transition from one color to another. What can be done? This function makes the chrominance transients (from one color to another) sharper without overshoot, undershoot or ringing. Image 8-8 CTI principle R5976584 BARCO CINE7 26022003...
V SYNC REF: INDIRECT CLAMP GATING: OFF LIMO PLUS OPTIONS FACTORY PRESET WARNING: ADVANCED ADJUSTMENT SHOULD BE PERFORMED ONLY BY QUALIFIED PERSONNEL Select with then <ENTER> <EXIT> to return Menu 8-39 R5976584 BARCO CINE7 26022003 8. Random Access Adjustment Mode Indirect...
GEOMETRY H PHASE RASTER SHIFT LEFT-RIGHT (E-W) TOP-BOTTOM (N-S) SIZE V LINEARITY BLANKING Select with then <ENTER> <EXIT> to return Menu 8-41 R5976584 BARCO CINE7 26022003...
The raster of the separate colors must be centered both horizontally and vertically on the center of the CRT surface. To center the raster, look into the lens of the respective color and use the cursor keys to move the raster. R5976584 BARCO CINE7 26022003 8. Random Access Adjustment Mode...
Note: Horizontal and Vertical shifts for Red and Blue should end up with a setting close to 50%. If these settings are significantly greater or lesser than 50%, contact a BARCO authorized service technician. 8. Press EXIT to return to the Geometry menu.
All adjustment are indicated on the screen with the function name, a bar scale and a number between 0 and 100. Adjust the next alignments until the vertical lines are straight. R5976584 BARCO CINE7 26022003 LEFT-RIGHT (E-W) V CENTERLINE BOW...
Use this correction only if, after adjusting the vertical lines with the side bow or side keystone, still a ’S’ deformation is visible on the left and the right side of the image. The default value on the bar scale for this correction is 50. R5976584 BARCO CINE7 26022003...
Only the green image is displayed while making left-right adjustments. The red and blue images will automat- ically be corrected in the same manner. Convergence corrections are automatically disabled for the duration of these adjustments. R5976584 BARCO CINE7 26022003 until a straight line is obtained (image 8-13) TOP-BOTTOM (N-S)
Page 78
Bottom bow • Bottom keystone All adjustment are indicated on the screen with the function name, a bar scale and a number between 0 and 100. Adjust the next alignments until the vertical lines are straight. R5976584 BARCO CINE7 26022003...
Page 79
(C) Top Bow (D) Top Keystone (E) Bottom Bow (F) Bottom Keystone How to enter an alignment? 1. Push the cursor key to highlight a function. 2. Press ENTER to activate this function. 3. Press EXIT to return. R5976584 BARCO CINE7 26022003...
What can be done? To adjust (correct) a little bit the horizontal and vertical picture size (when the projector is on its correct position) in regard with the installed screen. until a straight line is obtained (image 8-15) R5976584 BARCO CINE7 26022003...
Page 81
4. Press EXIT to return to the Geometry menu. GEOMETRY H PHASE RASTER SHIFT LEFT-RIGHT (E-W) TOP-BOTTOM (N-S) SIZE V LINEARITY BLANKING Select with then <ENTER> <EXIT> to return Menu 8-51 R5976584 BARCO CINE7 26022003 8. Random Access Adjustment Mode...
3. Adjust the vertical linearity with the cursor keys until the distances between the horizontal lines of the set up pattern are equal from top to bottom. (image 8-20) GEOMETRY H PHASE RASTER SHIFT LEFT-RIGHT (E-W) TOP-BOTTOM (N-S) SIZE V LINEARITY BLANKING Select with then <ENTER> <EXIT> to return Menu 8-52 Image 8-18 Horizontal Size Adjustment R5976584 BARCO CINE7 26022003...
Bottom Blanking Left Blanking Right Blanking If the internal # pattern was selected, this pattern remains on the screen. If the genlocked pattern was selected, the external source will be displayed. R5976584 BARCO CINE7 26022003 8. Random Access Adjustment Mode...
Adjust the red and blue until they exactly match with the green lines. BLANKING BOTTOM LEFT RIGHT Select with then <ENTER> <EXIT> to return Menu 8-54 R5976584 BARCO CINE7 26022003...
6. Press EXIT to return to the Convergence. 7. Repeat the same procedure for Red on Green and Blue on Green. 8. Press EXIT to return to the Random Access Adjustment Mode menu. R5976584 BARCO CINE7 26022003 CONVERGENCE GREEN ONLY...
Page 86
8. Random Access Adjustment Mode Image 8-24 25 Coarse Convergence Areas R5976584 BARCO CINE7 26022003...
Some items in the Service mode are password protected (when the password function is active). Enter your password to continue. All other password protected items are now also available if you stay in the adjustment mode. R5976584 BARCO CINE7 26022003 SERVICE MODE PROJECTOR SET UP...
Overview • Starting Up Projector Set-Up • Identification • Total Run Time • Change Password • Change Language • Change Projector Address • Change Baudrate • Power Up Mode Operating/Stand-By • Common Address • Barco Logo R5976584 BARCO CINE7 26022003...
The total system run time since the first start up can be displayed plus the run time of the separate CRT’s since the last reset. All projectors leave the factory after a burn-in period of approximately 100 hours. R5976584 BARCO CINE7 26022003 PROJECTOR SET-UP...
Password function is only active if the jumper on the controller is in the ’On’ position. Contact a qualified BARCO technician to activate the password if needed. The default password is 0000. How to Change the Password? 1.
The following baud rates are available: • 9600 • 4800 • 2400 • 1200 • • • • R5976584 BARCO CINE7 26022003 LANGUAGE ENGLISH ESPANOL FRANCAIS DEUTSCH Select with then <ENTER> <EXIT> to return Menu 9-12 PROJECTOR ADDRESS Enter new projector address:...
The reason to have the choice to select between common addresses is, to avoid controlling of other IR controlled units, e.g. a TV set with standard common address 0. BAUDRATE Select new baudrate: 9600 4800 2400 1200 Select with arrow keys: <ENTER> to accept <EXIT> to return Menu 9-16 R5976584 BARCO CINE7 26022003...
9.3.10 Barco Logo What can be done? The BARCO logo can be added to the image, in overlay or in background, on any place on the screen. Continuous use of the BARCO logo damages the RED CRT. R5976584 BARCO CINE7 26022003...
Select mode and toggle with ENTER between ON and OFF ON : BARCO logo will be displayed on the screen when leaving the adjustment mode. To position the logo on the screen, push the cursor key up, down, to the left or to the right until the desired position is reached.
Menu 9-23 9.4.3 Delete a Block This item is password protected. What can be done? This will delete the selected block. R5976584 BARCO CINE7 26022003 MEMORY MANAGEMENT COPY A BLOCK DELETE A BLOCK DELETE ALL BLOCKS ALL SETTINGS TO MIDPOS R &...
This item is password protected. DELETE MODE Nr.Src Fh Conf 15.6 50 Video 31.2 60 RGB3S 15.6 50 Intern FC 31.5 50 RGB3S 33.7 60 Intern FC Active block no. 1 Select with then <ENTER> <EXIT> to return Menu 9-26 R5976584 BARCO CINE7 26022003...
3. Press ENTER to confirm, press EXIT to cancel the reset. MEMORY MANAGEMENT COPY A BLOCK DELETE A BLOCK DELETE ALL BLOCKS ALL SETTINGS TO MIDPOS R & B CONVERGENCE MID GR CONVERGENCE MID Select with then <ENTER> <EXIT> to return Menu 9-30 R5976584 BARCO CINE7 26022003 9. Service Mode...
2. Press ENTER to reset the All settings to the previous settings. MEMORY MANAGEMENT COPY A BLOCK DELETE A BLOCK DELETE ALL BLOCKS ALL SETTINGS TO MIDPOS R & B CONVERGENCE MID UNDO GR CONVERGENCE MID Select with then <ENTER> <EXIT> to return Menu 9-33 R5976584 BARCO CINE7 26022003...
<EXIT> to return Menu 9-34 9.5.2 G2 Adjustment G2 adjustment should be performed by BARCO personnel, or BARCO authorized dealers How to start up G2 adjustment? 1. Push the cursor key to highlight G2 Adjustment and press ENTER to select. (menu 9-36) If you are qualified, press ENTER to continue.
A FULL WHITE PATTERN WILL BE GENERATED FOR 20 MINUTES AT POWER UP AFTER THIS PROCEDURE THE PROJECTOR IS READY TO PERFORM IN OPTIMUM CONDITIONS TOGGLE OPTION ON OR OFF with <ENTER> <EXIT> to return Menu 9-40 R5976584 BARCO CINE7 26022003...
COMMON SETTINGS I2C DIAGNOSTICS Select with then <ENTER> <EXIT> to return Menu 9-42 R5976584 BARCO CINE7 26022003 . The I2C address, IC number and module name will be given in I2C I2C DIAGNOSTICS Failures : Add IC number Mod. name IC200...
Page 102
9. Service Mode R5976584 BARCO CINE7 26022003...
TOP-BOTTOM (N-S) SIZE V LINEARITY BLANKING Select with then <ENTER> <EXIT> to return Menu 10-5 R5976584 BARCO CINE7 26022003 WARNING RISK OF INCORRECT Select a path from below : ADJUSTMENT OF THE PROJECTOR. The following SERVICE menus are reserved to,...
Blanking Right Factory predefined functions • F1 = IRIS Touch-Up • F2 = Convergence Red on Green • F3 = Convergence Blue on Green • F4 = H & V Size • F5 = Color Balance R5976584 BARCO CINE7 26022003...
WARNING: RCVDS not available WARNING: invalid frequency input WARNING: Option not installed ! R5976584 BARCO CINE7 26022003 11. Messages, Warnings and Failures When selecting a new source, following information about this source will be displayed on the screen: Source number, horizontal and vertical frequencies of the displayed source.
Hardware failure. Call a qualified service technician for repair. Serial communication error between the RCVDS and the projector. Input not valid Error in the communication between the projector and the PC. Projector switched off due to a fan fail. R5976584 BARCO CINE7 26022003...
(source numbers of the 800 peripheral). This file can contain different settings. The relationship between sources 1 - 9 of the 800 peripheral and 91 - 99 is shown in the diagram below. source input 1 source input 2 R5976584 BARCO CINE7 26022003 A. Source Numbers 81 — 86 and 91 — 96 file A file A’...
3 source input 93 source input 6 source input 96 source number 81 source number 82 source number 83 source number 84 source number 85 source number 86 file C file C’ file F file F’ R5976584 BARCO CINE7 26022003...
Short for progressive scanning. A system of video scanning whereby lines of a picture are transmitted consecutively, such as in the computer world Projector address Address installed in the projector to be individually controlled. RS232 A standard, single-ended (unbalanced) interconnection scheme for serial data communications. R5976584 BARCO CINE7 26022003 Glossary...
Source connections Connection RS232 Contrast Enhancement 38, 60 Convergence 80–81 Adjustment Start up Coring CRT Run In Cycle R5976584 BARCO CINE7 26022003 Decoding Factory Preset Frequencies Factory presets Failures 101–102 FCC Statement Fire Hazard Format Select 39–40 Add name Selecting...
Page 112
With Tri level composite sync Source connections RS232 Connection S-Video Source connections Safety Safety Indication Safety Instructions Safety Warning Service Menus Service Mode 83–84, 90 Introduction Memory Management Overview Projector Set up Start up Servicing Setup Pattern Selecting R5976584 BARCO CINE7 26022003...
Page 113
91 — 96 without 800 peripheral Split Screen On/Off Stand By Mode Start up Stationary Image Warning Switch off R5976584 BARCO CINE7 26022003 Switch on Switching ON/OFF Sync mode Fast/Slow Time Base Correction Total Run Time Trigger output...
Need help?
Do you have a question about the CINE7 R9010040 and is the answer not in the manual?
Questions and answers