Related Manuals for CellarCool RTN400
Summary of Contents for CellarCool RTN400
-
Page 1: Installation Manual
*CONFIDENTIAL* Fully Ducted Split Series 24V THERMOSTAT CONVERSION KIT Installation Manual (RTN400 & XW260K) 24V Thermostat Conversion Kit to be used in conjunction with Fully Ducted Split Series 091018 24VTCK.FD.Split.Series... - Page 2 CellarCool. Every effort has been made to ensure that the information in this manual is accurate. CellarCool is not responsible for printing or clerical errors.
- Page 3 Installation Instructions ........5 www.cellarcool.com | Page 1...
- Page 4 The 24V Thermostat Conversion Kit allows the customer the ability to utilize a 24V smart thermostat to control the operation of their CellarCool unit. Note: 24V Thermostat must be placed inside the wine cellar in a central location, away from direct airflow.
- Page 5 CellarCool Customer Service immediately. REMEMBER: Inspect the kit before installation. If damage is found, please contact your distributor or CellarCool Customer Service at 1-800-343-9463. 2. Verify that you have received all of the items on the component list below and that the kit corresponds with your specific CellarCool cooling system.
- Page 6 Note: If the unit is hard-wired to a dedicated power source, shut off the designated breaker. - DISCLAIMER - These instructions are universal for both the RTN400 & XW260K controllers. If your controller model is RTN400, skip the steps labeled XW260K ONLY.
- Page 7 Note: Use caution as plenum will not be supported once screws are removed. Remove plenum from unit and set aside. Remove thumb screw securing electrical panel in place. Slide electrical panel down and place hooks in electrical slots to hold in place. www.cellarcool.com | Page 5...
- Page 8 Remove the 4 screws from the enclosure lid using a #1 Phillips screw driver. RTN400 ONLY Locate Pb1, Pb2, DI and Display wires. RTN400 ONLY Disconnect Pb2, DI, Display, and Pb1 wires from the circuit board. RTN400 ONLY Remove the disconnected wires from the enclosure.
- Page 9 (pb1, pb2, display wires). XW260K ONLY Disconnect Pb1, Display, and Pb2 wires from the circuit board. XW260K ONLY Remove the rubber grommet and disconnected wires from the enclosure. XW260K ONLY Use wire cutters to remove the grommet. www.cellarcool.com | Page 7...
- Page 10 Unplug Molex connectors and separate the wires. Remove the Phillips screws securing the enclosure to the panel using a #2 Phillips screw driver. Separate controller assembly from the unit. Controller assembly is no longer needed. Isolate previously removed wires and secure with the provided cable tie.
- Page 11 Strip off 6” from the thermostat wire casing. Cut and remove white thermostat wire. Strip off about ¼” of the blue, red, green and yellow thermostat wire casing to expose the copper. 6” www.cellarcool.com | Page 9...
- Page 12 Locate the 24V Conversion Kit. Note: Conversion Kit will be mounted in the same location where the previous controller box was mounted. Mount the 24V Conversion Kit Enclosure in the location shown using the previously removed Phillips screws. Connect thermostat wires with the provided wire nuts by color matching red to red, blue to blue, green to green and yellow to yellow.
- Page 13 Secure wires to cable tie mount using cable tie. Slide electrical panel into compartment. Secure wires into electrical compartment. Reinstall thumb screw to secure electrical panel in place. www.cellarcool.com | Page 11...
- Page 14 Reinstall grille. Conversion process is now complete. The 24V Thermostat Conversion Kit has been successfully installed. 091018 24VTCK.FD.Split.Series Page 12 | 1-800-343-9463...
- Page 15 CellarCool 1738 E. Alpine Ave Stockton, CA 95205 1-800-343-9463 www.CellarCool.com 091018 24VTCK.FD.Split.Series...