GE CGS990SETSS Dimensions And Installation Information

CGS990SETSS
GE Café Series 30" Slide-In Front Control Gas
™
Double Oven with Convection Range
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
ELECTRICAL REQUIREMENTS: 120v; 60Hz, 15A
INSTALLATION INFORMATION: Before installing,
consult installation instructions packed with product
for current dimensional data.
1 1/2"
1 1/2"
25"
w/o handle
29 1/2"
w/handle
*43 3/4"
25"
w/o handle
29 1/2"
w/handle
*43 3/4"
*Dimensions are referenced from the point at the
back of the range that will contact the rear wall first.
*Dimension are referenced from the point at
the back of the range that will contact the rear
*Dimensions are referenced from the point at the
wall first. Max dimension should be considered
back of the range that will contact the rear wall first.
between the upper and lower doors.
*Dimension are referenced from the point at
**Height to backguard based on Café style
the back of the range that will contact the rear
backguard kit installed.
wall first. Max dimension should be considered
For answers to your Monogram, GE Café
between the upper and lower doors.
GE Appliances product questions, visit our website at geappliances.com
**Height to backguard based on Café style or call GE Answer Center
CGS990
backguard kit installed.
*Dimensions are referenced from the point at the
back of the range that will contact the rear wall first.
*Dimension are referenced from the point at
the back of the range that will contact the rear
wall first. Max dimension should be considered
between the upper and lower doors.
**Height to backguard based on Café style
backguard kit installed.
CGS990
Minimum to
cabinets on
either side
of the range.
36 1/4" +/- 1/4"
Minimum to
Minimum
18"
cabinets on
clearance
either side
to left wall
of the range.
36 1/4" +/- 1/4"
To cabinets Minimum
18"
clearance
below
to left wall
cooktop and
at the range
back
To cabinets
30"
below
cooktop and
at the range
For island installation, Model CGS990, maintain 2-1/2" minimum from cutout to back edge of countertop and 3"
back
minimum from cutout to side edges of countertop.
30"
For island installation, Model CGS990, maintain 2-1/2" minimum from cutout to back edge of countertop and 3"
minimum from cutout to side edges of countertop.
Gas Pipe and Electrical Outlet Locations
Gas Pipe and Electrical Outlet Locations
™ Series, GE Profile
® Service, 800.626.2000.
minimum from cutout to side edges of countertop.
Gas Pipe and Electrical Outlet Locations
Recommended area 120V
outlet on rear wall and area for
through-the-wall connection
of pipe stub and shut-off valve.
9"
Recommended area
for through-the-floor
connection of pipe stub
and shut-off valve.
30"
30"
6" 6"
Minimum
Minimum
clearance to
right wall
30"
30"
6" 6"
Minimum
Minimum
clearance to
0"
36" right wall
0"
36"
ADA
COMPLIANT
30"
™ Series or
4 1/2"
30"
4 1/2"
5"
30"
4 1/2"
5"
4"
8"
14 1/2"
CAUTION
2"
3"
To prevent drafts from affecting burner
operation, seal all openings in floor and wall.
Maximum
depth for
cabinets above
countertops
13"
Maximum
depth for
cabinets above
countertops
Front edge of
the range side
13"
panel forward
from cabinet
1/4"
Front edge of
the range side
panel forward
from cabinet
1/4"
All GE ranges are equipped with
an Anti-Tip device. The installation
of this device is an important,
required step in the installation
of the range.
0"
To cabinets below cooktop
and at the range back
(Some models will not have
0" clearance.)
0"
To cabinets below cooktop
and at the range back
(Some models will not have
0" clearance.)
Specification Revised 5/16